Example multicast DNAT configuration

The example topology shown and described below shows how to configure destination NAT (DNAT) for two multicast streams. Both of these streams originate from the same source IP address, which is 10.166.0.11. The example configuration keeps the streams separate by creating 2 multicast NAT policies.

In this example, the FortiGate devices have the following roles:

• FGT-1 is the RP for dirty networks, 233.0.0.0/8.
• FGT-2 performs all firewall and DNAT translations.
• FGT-3 is the RP for the clean networks, 239.254.0.0/16.
• FGT-1 and FGT-3 are functioning as PM enabled routers and could be replaced can be any PIM enabled router.

This example only describes the configuration of FGT-2.

FGT-2 performs NAT so that the receivers connected to FGT-3 receive the following translated multicast streams.

• If the multicast source sends multicast packets with a source and destination IP of 10.166.0.11 and 233.2.2.1, FGT-3 translates the source and destination IPs to 192.168.20.1 and 239.254.1.1
• If the multicast source sends multicast packets with a source and destination IP of 10.166.0.11 and 233.3.3.1, FGT-3 translates the source and destination IPs to 192.168.20.10 and 239.254.3.1

Example multicast DNAT topology

To configure FGT-2 for DNAT multicast

1. Add a loopback interface. In the example, the loopback interface is named loopback.

config system interface

edit loopback

set vdom root

set ip 192.168.20.1 255.255.255.0

set type loopback

next

end

2. Add PIM and add a unicast routing protocol to the loopback interface as if it was a normal routed interface. Also, add static joins to the loopback interface for any groups to be translated.

config router multicast

config interface

edit loopback

set pim-mode sparse-mode

config join-group

edit 233.2.2.1

next

edit 233.3.3.1

next

end

next

3. In this example, to add firewall multicast policies, different source IP addresses are required so you must first add an IP pool:

config firewall ippool

edit Multicast_source

set endip 192.168.20.20

set interface port6

set startip 192.168.20.10

next

end

4. Add the translation security policies. Policy 2, which is the source NAT policy, uses the actual IP address of port6. Policy 1, the DNAT policy, uses an address from the IP pool. The source and destination addresses will need to be previously created address objects. For this example, 233.3.3.1 255.255.255.255 will be represented by "example-addr_1" and 10.166.0.11 255.255.255.255 will be represented by "example-addr_2". You'll likely want to use something more intuitive from your own network.

config firewall multicast-policy

edit 1

set dnat 239.254.3.1

set dstaddr example-addr_1

set dstintf loopback

set nat 192.168.20.10

set srcaddr example-addr_2

set srcintf port6

next

edit 2

set dnat 239.254.1.1

set dstaddr 233.2.2.1 255.255.255.255

set dstintf loopback

set nat 192.168.20.1

set srcaddr 10.166.0.11 255.255.255.255

set srcintf port6

next

end

5. Add a firewall multicast policy to forward the stream from the loopback interface to the physical outbound interface. This example is an any/any policy that makes sure traffic accepted by the other multicast policies can exit the FortiGate.

config firewall multicast-policy

edit 3

set dstintf port7

set srcintf loopback

next

end