Inter-VDOM routing configuration example: Partial-mesh VDOMs

This example shows how to configure a FortiGate unit to use inter-VDOM routing to route traffic between an internal network and FTP server that are each behind separate VDOMs. See Inter-VDOM routing for more information.

The following example shows how to configure per-VDOM settings, such as operation mode, routing, and firewall policies, in a network that includes the following VDOMs:

• VDOM-A: allows the internal network to access the Internet.

• VDOM-B: allows external connections to an FTP server.

• root: the management VDOM.

You can use VDOMs in either NAT or transparent mode on the same FortiGate. By default, VDOMs operate in NAT mode. In this example, both VDOM-A and VDOM-B use NAT mode. An inter-VDOM link is created and inter-VDOM routes configured to allow users on the internal network to access the FTP server.

This is an example of the partial-mesh VDOMs configuration since only VDOM-A is connected to VDOM-B but neither of those VDOMs are connected to the root VDOM. See Topologies for details.

This example assumes that the interfaces of the FortiGate have already been configured with the IP addresses depicted in the preceding diagram.

General steps for this example

This configuration requires the following general steps:

1. Enable Multi VDOM mode and create the VDOMs

2. Assign interfaces to VDOMs

3. Configure VDOM-A

4. Configure VDOM-B

5. Configure the VDOM link

6. Configure inter-VDOM routing

7. Configure firewall policies using the VDOM link

This example demonstrates how to configure these steps first using the GUI and then, at the end of the section, using the CLI. See Configuration with the CLI for details.

Enable Multi VDOM mode and create the VDOMs

Multi VDOM mode can be enabled in the GUI or CLI. Enabling it does not require a reboot, but does log you out of the device. The current configuration is assigned to the root VDOM.

On FortiGate 90 series models and lower, VDOMs can only be enabled using the CLI.

To enable multi VDOM mode in the GUI:

1. On the FortiGate, go to System > Settings.

2. In the System Operation Settings section, enable Virtual Domains.

3. Click OK.

To create the VDOMs in the GUI:

1. In the Global VDOM, go to System > VDOM.

   Click Create New.

2. In the Virtual Domain field, enter VDOM-A.

   

3. If required, set the NGFW Mode. If the NGFW Mode is Profile-based, Central SNAT can be enabled.

4. Click OK to create the VDOM.

5. Repeat the above steps for VDOM-B.

Assign interfaces to VDOMs

This example uses three interfaces on the FortiGate unit: port1 (internal network), port2 (FTP server), wan1 (WAN link for VDOM-A), and wan2 (WAN link for VDOM-B). The port1 and port2 interfaces are connected to the internal network and FTP server, respectively. The wan1 and wan2 interfaces are static assigned with IP addresses and default gateways provided by the ISPs for those WAN links.

To assign interfaces to VDOMs in the GUI:

1. In the Global VDOM, go to Network > Interfaces.

2. Select port1 and click Edit.

3. From the Virtual domain list, select VDOM-A.

   

4. Click OK.

5. Repeat the preceding steps to assign port2 to VDOM-B.

6. Repeat the preceding steps to assign wan1 to VDOM-A.

7. Repeat the preceding steps to assign wan2 to VDOM-B.

Configure VDOM-A

VDOM-A allows connections from devices on the internal network to the Internet. WAN1 and port1 are assigned to this VDOM.

The per-VDOM configuration for VDOM-A includes the following:

• A firewall address for the internal network

• A static route to the ISP gateway

• A firewall policy allowing the internal network to access the Internet

All procedures in this section require you to connect to VDOM-A, either using a global or per-VDOM administrator account.

To add the firewall addresses in the GUI:

1. Go to Policy & Objects > Addresses.

2. Click Create New > Address.

3. Enter the following information:

   Name	internal-network
   Type	Subnet
   IP/Netmask	192.168.10.0/255.255.255.0
   Interface	port1

4. Click OK.

To add a default route in the GUI:

1. Go to Network > Static Routes and create a new route.

2. Enter the following information:

   Destination	Subnet
   IP address	0.0.0.0/0.0.0.0
   Gateway	172.20.201.254
   Interface	wan1
   Administrative Distance	10

3. Click OK.

To add the firewall policy in the GUI:

1. Go to Policy & Objects > Firewall Policy.

2. Click Create New.

3. Enter the following information:

   Name	VDOM-A-Internet
   Incoming Interface	port1
   Outgoing Interface	wan1
   Source	internal-network
   Destination	all
   Schedule	always
   Service	ALL
   Action	ACCEPT
   NAT	enabled

4. Click OK.

Configure VDOM-B

VDOM-B allows external connections to reach an internal FTP server. WAN2 and port2 are assigned to this VDOM.

The per-VDOM configuration for VDOM-B includes the following:

• A firewall address for the FTP server

• A virtual IP address for the FTP server

• A static route to the ISP gateway

• A firewall policy allowing external traffic to reach the FTP server

The procedures described above require you to connect to VDOM-B, either using a global or per-VDOM administrator account.

To add the firewall addresses in the GUI:

1. Go to Policy & Objects > Addresses.

2. Click Create New > Address.

3. Enter the following information:

   Name	FTP-server
   Type	Subnet
   IP/Netmask	192.168.10.0/255.255.255.255
   Interface	port2

4. Click OK.

To add the virtual IP address in the GUI:

1. Go to Policy & Objects > Virtual IPs.

2. Click Create New > Virtual IP.

3. Enter the following information:

   Name	FTP-server-VIP
   Interface	wan2
   External IP address/range	172.20.10.2
   Map To	192.168.20.10

4. Click OK.

To add a default route in the GUI:

1. Go to Network > Static Routes and create a new route.

2. Enter the following information:

   Destination	Subnet
   IP address	0.0.0.0/0.0.0.0
   Gateway	172.20.201.254
   Interface	wan2
   Administrative Distance	10

3. Click OK.

To add the firewall policy in the GUI:

1. Go to Policy & Objects > Firewall Policy.

2. Click Create New.

3. Enter the following information:

   Name	Access-server
   Incoming Interface	wan2
   Outgoing Interface	port2
   Source	all
   Destination	FTP-server-VIP
   Schedule	always
   Service	FTP
   Action	ACCEPT
   NAT	enabled

4. Click OK.

Configure the VDOM link

The VDOM link allows connections from VDOM-A to VDOM-B. The VDOM link interface configured in this step will be used for inter-VDOM routing.

This step requires you to connect to the global VDOM using a global administrator account.

To add the VDOM link in the GUI:

1. In the Global VDOM, go to Network > Interfaces.

2. Create New > VDOM link.

3. Enter the following information:

   Name		VDOM-link
   Interface 0
   	Virtual Domain	VDOM-A
   	IP/Netmask	11.11.11.1/255.255.255.252
   Interface 1
   	Virtual Domain	VDOM-B
   	IP/Netmask	11.11.11.2/255.255.255.252

4. Click OK.

Configure inter-VDOM routing

Inter-VDOM routing allows users on the internal network to route traffic to the FTP server through the FortiGate.

The configuration of inter-VDOM routing includes the following:

• Firewall addresses for the FTP server on VDOM-A and for the internal network on VDOM-B

• Inter-VDOM routing using static routes for the FTP server on VDOM-A and for the internal network on VDOM-B

• Policies allowing traffic using the VDOM link

The procedures described above require you to connect to both VDOM-A and VDOM-B, either using a global or per-VDOM administrator account.

To add the firewall address on VDOM-A in the GUI:

1. In the VDOM-A VDOM, go to Policy & Objects > Addresses.

2. Click Create New > Address.

3. Enter the following information:

   Name	FTP-server
   Type	Subnet
   IP/Netmask	192.168.20.10/32
   Interface	VDOM-link2
   Static route configuration	enabled

4. Click OK.

To add the static route on VDOM-A in the GUI:

1. Connect to VDOM-A.

2. Go to Network > Static Routes and create a new route.

3. Enter the following information:

   Destination	Named Address
   Named Address	FTP-server
   Gateway	11.11.11.2
   Interface	VDOM-link0

4. Click OK.

To add the firewall address on VDOM-B in the GUI:

1. In the VDOM-B VDOM, go to Policy & Objects > Addresses.

2. Click Create New > Address.

3. Enter the following information:

   Name	internal-network
   Type	Subnet
   IP/Netmask	192.168.10.0/24
   Interface	VDOM-link1
   Static route configuration	enabled

4. Click OK.

To add the static route on VDOM-B in the GUI:

1. In the VDOM-B VDOM, go to Network > Static Routes and create a new route.

2. Enter the following information:

   Destination	Named Address
   Named Address	internal-network
   Gateway	11.11.11.1
   Interface	VDOM-link1

3. Click OK.

Configure firewall policies using the VDOM link

Firewall policies using the VDOM link allows users on the internal network to access the FTP server through the FortiGate.

Configuring policies allowing traffic using the VDOM link require you to connect to both VDOM-A and VDOM-B, respectively, either using a global or per-VDOM administrator account.

To add the firewall policy on VDOM-A in the GUI:

1. In the VDOM-A VDOM, go to Policy & Objects > Firewall Policy.

2. Click Create New.

3. Enter the following information:

   Name	Access-FTP-server
   Incoming Interface	port1
   Outgoing Interface	VDOM-link0
   Source	internal-network
   Destination	FTP-server
   Schedule	always
   Service	FTP
   Action	ACCEPT
   NAT	disabled

4. Click OK.

To add the firewall policy on VDOM-B in the GUI:

1. In the VDOM-B VDOM, go to Policy & Objects > Firewall Policy.

2. Click Create New.

3. Enter the following information:

   Name	Internal-server-access
   Incoming Interface	VDOM-link1
   Outgoing Interface	port2
   Source	internal-network
   Destination	FTP-server
   Schedule	always
   Service	FTP
   Action	ACCEPT
   NAT	disabled

4. Click OK.

Configuration with the CLI

The example can also be configured in the CLI.

To configure the two VDOMs:

1. Enable multi VDOM mode:

   config system global
       set vdom-mode multi-vdom
   end

   You will be logged out of the device when VDOM mode is enabled.

2. Create the VDOMs:

   config vdom
       edit VDOM-A
       next
       edit VDOM-B
       next
   end

3. Assign interfaces to the VDOMs:

   config global
       config system interface
           edit port1
               set vdom VDOM-A
           next
           edit port2
               set vdom VDOM-B
           next
           edit wan1
               set vdom VDOM-A
           next
           edit wan2
               set vdom VDOM-B
           next
       end
   end

4. Add the firewall addresses to VDOM-A:

   config vdom
       edit VDOM-A
           config firewall address
               edit internal-network
                   set associated-interface port1
                   set subnet 192.168.10.0 255.255.255.0
               next
           end
       next
   end

5. Add a default route to VDOM-A:

   config vdom
       edit VDOM-A
           config router static
               edit 0
                   set gateway 172.20.201.254
                   set device wan1
               next
           end
       next
   end

6. Add the firewall policy to VDOM-A:

   config vdom
       edit VDOM-A
           config firewall policy
               edit 1
                   set name "VDOM-A-Internet"
                   set srcintf "port1"
                   set dstintf "wan1"
                   set srcaddr "internal-network"
                   set dstaddr "all"
                   set action accept
                   set schedule "always"
                   set service "ALL"
                   set nat enable
               next
           end
       next
   end

7. Add the firewall addresses to VDOM-B:

   config vdom
       edit VDOM-B
           config firewall address
               edit FTP-server
                   set associated-interface port2
                   set subnet 192.168.20.10 255.255.255.255
               next
           end
       next
   end

8. Add the virtual IP address to VDOM-B:

   config vdom
       edit VDOM-B
           config firewall vip 
               edit FTP-server-VIP
                   set extip 172.20.10.2
                   set extintf wan2
                   set mappedip 192.168.20.10
               next
           end 
       next
   end

9. Add a default route to VDOM-B:

   config vdom
       edit VDOM-B
           config router static
               edit 0
                   set gateway 172.20.10.254
                   set device wan2
               next
           end
       next
   end

10. Add the firewall policy to VDOM-B:

    config vdom
        edit VDOM-B
            config firewall policy
                edit 1
                    set name "Access-server"
                    set srcintf "wan2"
                    set dstintf "port2"
                    set srcaddr "all"
                    set dstaddr "FTP-server-VIP"
                    set action accept
                    set schedule "always"
                    set service "FTP"
                    set nat enable
                next
            end
        next
    end

To configure the VDOM link:

1. Configure the VDOM link:

   config global
       config system vdom-link
           edit "VDOM-link"
           next
       end    
       config system interface
           edit VDOM-link0
               set vdom VDOM-A
               set ip 11.11.11.1 255.255.255.252
               set allowaccess https ping ssh
               set description "VDOM-A side of the VDOM link"
           next
           edit VDOM-link1
               set vdom VDOM-B
               set ip 11.11.11.2 255.255.255.252
               set allowaccess https ping ssh
               set description "VDOM-A side of the VDOM link"
           next
       end
   end

2. Configure the firewall addresses on VDOM-A:

   config vdom
       edit VDOM-A
           config firewall address
               edit "FTP-server"
                   set associated-interface "VDOM-link0"
                   set allow-routing enable
                   set subnet 192.168.20.10 255.255.255.255
               next
           end
       next
   end

3. Add the firewall policy to VDOM-B:

   config vdom
       edit VDOM-B
           config firewall policy
               edit 1
                   set name "Access-server"
                   set srcintf "wan2"
                   set dstintf "port2"
                   set srcaddr "all"
                   set dstaddr "FTP-server-VIP"
                   set action accept
                   set schedule "always"
                   set service "FTP"
                   set nat enable
               next
           end
       next
   end

4. Add the static route on VDOM-A:

   config vdom
       edit VDOM-A
           config router static 
               edit 0
                   set device VDOM-link0
                   set dstaddr FTP-server
                   set gateway 11.11.11.2 
               next
           end
       next
   end

5. Configure the firewall addresses on VDOM-B:

   config vdom
       edit VDOM-B
           config firewall address
               edit internal-network
                   set associated-interface VDOM-link1
                   set allow-routing enable
                   set subnet 192.168.10.0 255.255.255.0
               next
           end
       next
   end

6. Add the static route on VDOM-B:

   config vdom
       edit VDOM-B
           config router static 
               edit 0
                   set device VDOM-link1
                   set dstaddr internal-network
                   set gateway 11.11.11.1
               next
           end
       next
   end

7. Add the security policy on VDOM-A:

   config vdom
       edit VDOM-A
           config firewall policy 
               edit 0
                   set name Access-FTP-server
                   set srcintf port1
                   set dstintf VDOM-link0
                   set srcaddr internal-network
                   set dstaddr FTP-server
                   set action accept
                   set schedule always
                   set service FTP
               next
           end
       next
   end

8. Add the firewall policy on VDOM-B:

   config vdom
       edit VDOM-B
           config firewall policy 
               edit 0
                   set name Internal-server-access
                   set srcintf VDOM-link1
                   set dstintf port2
                   set srcaddr internal-network
                   set dstaddr FTP-server
                   set action accept
                   set schedule always
                   set service FTP
               next
           end
       next
   end