HA using a hardware switch to replace a physical switch

An HA cluster can be deployed without physical switches connecting the traffic interfaces on the primary and secondary members. This setup may be desirable in certain environments where the network infrastructure must be kept to a bare minimum.

Generally, using a hardware switch to replace a physical switch is not recommended, as it offers no redundancy or interface monitoring.

• If one FortiGate loses power, all of the clients connected to that FortiGate device cannot go to another device until that FortiGate recovers.

• A hardware switch cannot be used as a monitor interface in HA. Any incoming or outgoing link failures on hardware member interfaces will not trigger failover; this can affect traffic.

Therefore, assess your environment thoroughly before applying this solution.

Examples

The examples use the following topology:

Traffic between hardware switches

When using Hardware switch in HA environment, a client device connected to the hardware switch on the primary FortiGate can communicate with client devices connected to the hardware switch on secondary FortiGates as long as there is a direct connection between the two switches.

No configuration is required after setting up the hardware switches. If a client connected to both of the hardware switches needs to reach destinations outside of the cluster, the firewall must be configured for it.

To configure the FortiGate devices:

1. Connect the devices as shown in the topology diagram.
2. On each FortiGate, configure HA:

   config system ha
       set mode a-a
       set group-name Example_cluster
       set hbdev ha1 10 ha2 20
   end 

3. On the primary FortiGate, configure the hardware switch:

   config system virtual-switch
       edit Hardware-SW
           set physical-switch sw0
           config port
               edit port3
               next
               edit port5
               next
           end
       next
   end

4. On each FortiGate, configure the IP addresses on the hardware switches:

   config system interface
       edit Hardware-SW
           set ip 6.6.6.1 255.255.255.0
           set allowaccess ping ssh http https
       next
   end

   After configuring the hardware switches, PC1 and PC2 can now communicate with each other.

Traffic passes through FortiGate

If client device needs to send traffic through the FortiGate, additional firewall configuration on the FortiGate is required.

All traffic from the hardware switches on either the primary or secondary FortiGate reaches the primary FortiGate first. The traffic is then directed according to the HA mode and firewall configuration.

To configure the FortiGate devices:

1. Connect the devices as shown in the topology diagram.
2. On each FortiGate, configure HA:

   config system ha
       set mode a-a
       set group-name Example_cluster
       set hbdev ha1 10 ha2 20
   end 

3. On the primary FortiGate, configure the hardware switch:

   config system virtual-switch
       edit Hardware-SW
           set physical-switch sw0
           config port
               edit port3
               next
               edit port5
               next
           end
       next
       edit Hardware-SW2
           set physical-switch sw0
           config port
               edit port1
               next
           end
       next
   end

4. On each FortiGate, configure the IP addresses on the hardware switch:

   config system interface
       edit Hardware-SW
           set ip 6.6.6.1 255.255.255.0
           set allowaccess ping ssh http https
       next
       edit Hardware-SW2
           set ip 172.16.200.1 255.255.255.0
           set allowaccess ping ssh http https
       next
   end

5. On each FortiGate, configure a firewall policy:

   config firewall policy
       edit 1
           set srcintf Hardware-SW
           set dstintf Hardware-SW2
           set srcaddr all
           set dstaddr all
           set service ALL
           set action accept
           set schedule always
           set nat enable
       next
   end

6. On each FortiGate, configure a static route:

   config router static
       edit 1
           set device Hardware-SW2
           set gateway 172.16.200.254
       next
   end

   Traffic from PC1 and PC2 can now reach destinations outside of the FortiGate cluster.