Fortinet Document Library

Version:

Version:

Version:

Version:

Version:

Version:

Version:

Version:

Version:

Version:

Version:

Version:

Version:

Version:

Version:

Version:

Version:

Version:

Version:

Version:

Version:

Version:


Table of Contents

Administration Guide

Configuring HA options

To configure HA options go to System Settings > HA and configure FortiAnalyzer units to create an HA cluster or change cluster configuration.

In System Settings > HA, use the Cluster Settings pane to create or change HA configuration, and use the Cluster Status pane to monitor HA status.

To configure a cluster, set the Operation Mode of the primary unit to High Availability. Then add the IP addresses and serial numbers of each secondary unit to the primary unit peer list. The IP address and serial number of the primary unit and all secondary units must be added to each secondary unit's HA configuration. The primary unit and all secondary units must have the same Group Name, Group ID and Password.

You can connect to the primary unit GUI to work with FortiAnalyzer. Using configuration synchronization, you can configure and work with the cluster in the same way as you work with a standalone FortiAnalyzer unit.

Configure the following settings:

Cluster Status

 

 

Operation Mode

Select High Availability to configure the FortiAnalyzer unit for HA.

Select Standalone to stop operating in HA mode.

 

Preferred Role

Select the preferred role when this unit first joins the HA cluster.

If the preferred role is Primary, then this unit becomes the primary unit if it is configured first in a new HA cluster. If there is an existing primary unit, then this unit becomes a secondary unit.

The default is Secondary so that the unit can synchronize with the primary unit. A secondary unit cannot become a primary unit until it is synchronized with the current primary unit.

Cluster Virtual IP

 

Interface

The interface the FortiAnalyzer HA unit uses to provide redundancy.

 

IP Address

The IP address for which the FortiAnalyzer HA unit is to provide redundancy.

Cluster Settings

 

Peer IP

Type the IP address of another FortiAnalyzer unit in the cluster.

 

Peer SN

Type the serial number of the FortiAnalyzer unit corresponding to the entered IP address.

 

Group Name

Type a group name that uniquely identifies the FortiAnalyzer HA cluster. All units in a cluster must have the same Group Name, Group ID and Password.

 

Group ID

Type a group ID from 1 to 255 that uniquely identifies the FortiAnalyzer HA cluster.

 

Password

A password for the HA cluster. All members of the HA cluster must have the same password.

 

Heart Beat Interval

The time the primary unit waits between sending heartbeat packets, in seconds. The heartbeat interval is also the amount of time that secondary units waits before expecting to receive a heartbeat packet from the primary unit.

 

Priority

The priority or seniority of the secondary unit in the cluster.

 

Log Data Sync

This option is on by default. It provides real-time log synchronization among cluster members.

Configuring HA options

To configure HA options go to System Settings > HA and configure FortiAnalyzer units to create an HA cluster or change cluster configuration.

In System Settings > HA, use the Cluster Settings pane to create or change HA configuration, and use the Cluster Status pane to monitor HA status.

To configure a cluster, set the Operation Mode of the primary unit to High Availability. Then add the IP addresses and serial numbers of each secondary unit to the primary unit peer list. The IP address and serial number of the primary unit and all secondary units must be added to each secondary unit's HA configuration. The primary unit and all secondary units must have the same Group Name, Group ID and Password.

You can connect to the primary unit GUI to work with FortiAnalyzer. Using configuration synchronization, you can configure and work with the cluster in the same way as you work with a standalone FortiAnalyzer unit.

Configure the following settings:

Cluster Status

 

 

Operation Mode

Select High Availability to configure the FortiAnalyzer unit for HA.

Select Standalone to stop operating in HA mode.

 

Preferred Role

Select the preferred role when this unit first joins the HA cluster.

If the preferred role is Primary, then this unit becomes the primary unit if it is configured first in a new HA cluster. If there is an existing primary unit, then this unit becomes a secondary unit.

The default is Secondary so that the unit can synchronize with the primary unit. A secondary unit cannot become a primary unit until it is synchronized with the current primary unit.

Cluster Virtual IP

 

Interface

The interface the FortiAnalyzer HA unit uses to provide redundancy.

 

IP Address

The IP address for which the FortiAnalyzer HA unit is to provide redundancy.

Cluster Settings

 

Peer IP

Type the IP address of another FortiAnalyzer unit in the cluster.

 

Peer SN

Type the serial number of the FortiAnalyzer unit corresponding to the entered IP address.

 

Group Name

Type a group name that uniquely identifies the FortiAnalyzer HA cluster. All units in a cluster must have the same Group Name, Group ID and Password.

 

Group ID

Type a group ID from 1 to 255 that uniquely identifies the FortiAnalyzer HA cluster.

 

Password

A password for the HA cluster. All members of the HA cluster must have the same password.

 

Heart Beat Interval

The time the primary unit waits between sending heartbeat packets, in seconds. The heartbeat interval is also the amount of time that secondary units waits before expecting to receive a heartbeat packet from the primary unit.

 

Priority

The priority or seniority of the secondary unit in the cluster.

 

Log Data Sync

This option is on by default. It provides real-time log synchronization among cluster members.