Configuring L3 Roaming for Bridge Mode SSIDs

L3 roaming inter-controller topology using bridge mode SSIDs supports two roaming modes:

• Indirect Mode

  In indirect mode, the L3 handoff is handled by the mobility tunnel between the FortiGate Wireless Controllers.

  

• Direct Mode

  In direct mode, the two FortiAPs must be able to reach each other with no NAT in the path and the L3 handoff occurs between the FortiAPs directly.

  

Direct mode is preferred if it is feasible in the topology.

The following configurations require dynamic user VLAN assignment by RADIUS to be configured for RADIUS users per the steps in VLAN assignment by RADIUS, specifically, configuring RADIUS user attributes that are used for the VLAN ID assignment.

To configure Intra-Controller L3 roaming for a bridge mode SSID - CLI:

1. Configure the client-idle-rehome-timeout (default is 20 seconds):

   config wireless-controller timers
     set client-idle-rehome-timeout 20
   end

2. configure the L3 roaming support bridge mode SSID and related VLAN interface:

    config wireless-controller vap
       edit "l3_br1"
           set ssid "L3Roaming_br1"
           set security wpa2-only-enterprise
           set auth radius
           set radius-server "wifi-radius"
           set local-bridging enable
           set schedule "always"
           set dynamic-vlan enable
           set l3-roaming enable
       next
   end
   config system interface
       edit "lan"
           set vdom "root"
           set ip 10.40.0.1 255.255.255.0
           set allowaccess ping https ssh http fabric
           set type hard-switch
           set stp enable
           set role lan
           set snmp-index 4
       next
   end
   config system interface
       edit "lan_100"
           set vdom "root"
           set ip 10.43.100.1 255.255.255.0
           set allowaccess ping
           set device-identification enable
           set role lan
           set snmp-index 10
           set interface "lan"
           set vlanid 100
       next
   end
   

3. Assign L3 roaming VAP to FAP433F:

   config wireless-controller wtp-profile
       edit "433F"
           config platform
               set type 433F
               set ddscan enable
           end
           set handoff-sta-thresh 55
           config radio-1
               set mode disabled
           end
           config radio-2
               set band 802.11ax-5G
               set vap-all manual
               set vaps "l3_br1"
               set channel "36"
           end
           config radio-3
               set mode disabled
           end
       next
   end
   config wireless-controller wtp
       edit "FP433FXX00000000"
           set uuid b04f1cca-8528-51ec-2dc0-c744cbef4179
           set admin enable
           set wtp-profile "433F"
           config radio-2
           end
       next
   end
   

4. Assign L3 roaming VAP to FAP831F:

   config wireless-controller wtp-profile
       edit "831F.1"
           config platform
               set type 831F
               set ddscan enable
           end
           set handoff-sta-thresh 55
           set allowaccess https ssh
           config radio-1
               set mode disabled
           end
           config radio-2
               set band 802.11ax-5G
               set power-level 99
               set vap-all manual
               set vaps "l3_br1"
               set channel "36" "40"
           end
           config radio-3
               set mode disabled
           end
       next
   end
   config wireless-controller wtp
       edit "FP831FXX00000000"
           set uuid b867ca7c-cbc5-51ec-d5ac-4a395282be68
           set admin enable
           set wtp-profile "831F.1"
           config radio-2
           end
       next
   end
   

To configure Inter-Controller L3 roaming for a bridge mode SSID - CLI:

This configuration requires two FortiGate units. In order to enable L3 roaming supported VAP, both FortiGate units must have the same SSID, security, and passphrase.

The following example uses:

• AC1 as FGT40F

  • FAP1 as FAP433E

• AC2 as FGT81EP

  • FAP2 as FAP831F

1. Configure the L3 roaming peer IP for AC1 (FGT-40F):

   config system interface
     edit "wan"
       set vdom "root"
       set ip 10.43.1.40 255.255.255.0
       set allowaccess ping https ssh http fabric
       set type physical
       set role wan
       set snmp-index 1
     next
   end
   config wireless-controller inter-controller
     set l3-roaming enable
     config inter-controller-peer
       edit 1
         set peer-ip 10.43.1.81
       next
     end
   end
   

   1. Configure the client-idle-rehome-timeout (default is 20 seconds):

      config wireless-controller timers
        set client-idle-rehome-timeout 20
      end

   2. Configure the L3 roaming support bridge mode SSID and related VLAN interface:

      config wireless-controller vap
          edit "l3_br1"
              set ssid "L3Roaming_br1"
              set security wpa2-only-enterprise
              set auth radius
              set radius-server "wifi-radius"
              set local-bridging enable
              set schedule "always"
              set dynamic-vlan enable
              set l3-roaming enable
              set l3-roaming-mode indirect
          next
      end
      config system interface
          edit "lan"
              set vdom "root"
              set ip 10.40.0.1 255.255.255.0
              set allowaccess ping https ssh http fabric
              set type hard-switch
              set stp enable
              set role lan
              set snmp-index 4
          next
      end
      config system interface
          edit "lan_100"
              set vdom "root"
              set ip 10.43.100.1 255.255.255.0
              set allowaccess ping
              set device-identification enable
              set role lan
              set snmp-index 10
              set interface "lan"
              set vlanid 100
          next
      end
      

   3. Assign L3 roaming VAP to FAP433F:

      config wireless-controller wtp-profile
          edit "433F"
              config platform
                  set type 433F
                  set ddscan enable
              end
              set handoff-sta-thresh 55
              config radio-1
                  set mode disabled
              end
              config radio-2
                  set band 802.11ax-5G
                  set vap-all manual
                  set vaps "l3_br1"
                  set channel "36"
              end
              config radio-3
                  set mode disabled
              end
          next
      end
      config wireless-controller wtp
          edit "FP433FXX00000000"
              set uuid b04f1cca-8528-51ec-2dc0-c744cbef4179
              set admin enable
              set wtp-profile "433F"
              config radio-2
              end
          next
      end
      

2. Configure the L3 roaming peer IP for AC2 (FGT-81EP):

   config system interface
     edit "wan1"
       set vdom "root"
       set ip 10.43.1.81 255.255.255.0
       set allowaccess ping https ssh http fabric
       set type physical
       set role wan
       set snmp-index 1
     next
   end
   config wireless-controller inter-controller
     set l3-roaming enable
     config inter-controller-peer
       edit 1
         set peer-ip 10.43.1.40
       next
     end
   end
   

   1. Configure the client-idle-rehome-timeout (default is 20 seconds):

      config wireless-controller timers
        set client-idle-rehome-timeout 20
      end

   2. Configure the L3 roaming support bridge mode SSID and related VLAN interface:

      config wireless-controller vap
          edit "l3_br1"
              set ssid "L3Roaming_br1"
              set security wpa2-only-enterprise
              set auth radius
              set radius-server "wifi-radius"
              set local-bridging enable
              set schedule "always"
              set dynamic-vlan enable
              set l3-roaming enable
              set l3-roaming-mode indirect
          next
      end
      config system interface
          edit "lan_hw"
              set vdom "root"
              set ip 10.81.0.129 255.255.255.0
              set allowaccess ping https ssh http fabric
              set type hard-switch
              set stp enable
              set role lan
              set snmp-index 52
          next
      end
      config system interface
          edit "lan_100"
              set vdom "root"
              set ip 10.81.100.1 255.255.255.0
              set allowaccess ping
              set device-identification enable
              set role lan
              set snmp-index 34
              set interface "lan_hw"
              set vlanid 100
          next
      end
      

   3. Assign L3 roaming VAP to FAP831F:

      config wireless-controller wtp-profile
          edit "831F.1"
              config platform
                  set type 831F
                  set ddscan enable
              end
              set handoff-sta-thresh 55
              set allowaccess https ssh
              config radio-1
                  set mode disabled
              end
              config radio-2
                  set band 802.11ax-5G
                  set power-level 99
                  set vap-all manual
                  set vaps "l3_br1"
                  set channel "36" "40"
              end
              config radio-3
                  set mode disabled
              end
          next
      end
      config wireless-controller wtp
          edit "FP831FXX00000000"
              set uuid b867ca7c-cbc5-51ec-d5ac-4a395282be68
              set admin enable
              set wtp-profile "831F.1"
              config radio-2
              end
          next
      end
      

3. Check the peer status from AC1 (FGT-40F):

   FortiGate-40F  # diagnose wireless-controller wlac -c ha
   WC fast failover info
       mode    : disabled 
       l3r     : enabled 
       peer cnt: 1 
                 FG81EPXX00000000 10.43.1.81:5246       UP 0
   

4. Check the peer status from AC2 (FGT-81EP):

   FortiGate-81E-POE # diagnose wireless-controller wlac -c ha
   WC fast failover info
       mode    : disabled 
       l3r     : enabled 
       peer cnt: 1 
                 FGT40FXX00000000 10.43.1.40:5246       UP 0
   

Understanding L3 roaming events for inter-controller L3 roaming for a bridge mode SSID

When the wireless client is connected with "L3Roaming_br1" on AP1 in AC1, the client receives IP 10.43.100.2 from AP1 in AC1, bridged to "lan_100" VLAN interface:

FortiGate-40F # diagnose wireless-controller wlac -d sta online
   vf=0 wtp=2 rId=2 wlan=l3_br1 vlan_id=100 ip=10.43.100.2 ip6=fe80::c84:737e:2ba0:7ae2 mac=22:cf:0e:1a:7f:d2 vci= host= user=vlan0100 group=wifi-radius signal=-67 noise=-95 idle=6 bw=0 use=6 chan=36 radio_type=11AC security=wpa2_only_enterprise mpsk= encrypt=aes cp_authed=no l3r=1,0 G=0.0.0.0:0,0.0.0.0:0-0-0 -- 0.0.0.0:0 0,0 online=yes mimo=2

When the client leaves AP1 and roams towards AP2, it connects with the same SSID "L3Roaming_br1" on AP2. Wireless traffic passes from AP2 and is sent to AC2. Eventually the wireless traffic is transferred from AC2 to AC1 and traffic is maintained from AC1. The wireless client maintains the original IP of 10.43.100.2:

FortiGate-81E-POE # diagnose wireless-controller wlac -d sta online
   vf=0 wtp=10 rId=2 wlan=l3_br1 vlan_id=0 ip=10.43.100.2 ip6=:: mac=22:cf:0e:1a:7f:d2 vci= host= user=vlan0100 group=wifi-radius signal=-58 noise=-95 idle=1 bw=5 use=7 chan=36 radio_type=11AC security=wpa2_only_enterprise mpsk= encrypt=aes cp_authed=no l3r=0,1 G=0.0.0.0:0,0.0.0.0:0-0-0 -- 0.0.0.0:0 0,0 online=yes mimo=2

If the wireless client idle time exceeds client-idle-rehome-timeout, it triggers the rehome event. The wireless client will send a DHCP request and obtain a new IP address from AC2 (10.81.100.2). Now the wireless client traffic is maintained from AC2:

FortiGate-81E-POE # diagnose wireless-controller wlac -d sta online
   L vf=0 wtp=10 rId=2 wlan=l3_br1 vlan_id=100 ip=10.81.100.2 ip6=fe80::c84:737e:2ba0:7ae2 mac=22:cf:0e:1a:7f:d2 vci= host= user=vlan0100 group=wifi-radius signal=-55 noise=-95 idle=3 bw=0 use=6 chan=36 radio_type=11AC security=wpa2_only_enterprise mpsk= encrypt=aes cp_authed=no l3r=1,0 G=0.0.0.0:0,0.0.0.0:0-0-0 -- 0.0.0.0:0 0,0 online=yes mimo=2