Basic wireless network example

This example uses automatic configuration to set up a basic wireless network.

To configure this wireless network, perform the following tasks:

Configuring authentication for wireless users
Configuring the SSID
Adding the SSID to the FortiAP Profile
Configuring security policies
Connecting the FortiAP units

Configuring authentication for wireless users

You need to configure user accounts and add the users to a user group. This example shows only one account, but multiple accounts can be added as user group members.

To configure a WiFi user - GUI

Go to User & Authentication > User Definition and select Create New.
Select Local User and then click Next.
Enter a User Name and Password and then click Next.
Click Next.
Make sure that Enable is selected and then click Create.

To configure the WiFi user group - GUI

Go to User & Device > User Groups and select Create New.
Enter the following information and then select OK:

Name	wlan_users
Type	Firewall
Members	Add users.

To configure a WiFi user and the WiFi user group - CLI

config user user

edit "user01"

set type password

set passwd "asdf12ghjk"

end

config user group

edit "wlan_users"

set member "user01"

end

Configuring the SSID

First, establish the SSID (network interface) for the network. This is independent of the number of physical access points that will be deployed. The network assigns IP addresses using DHCP.

To configure the SSID - GUI

Go to WiFi and Switch Controller > SSIDs and select Create New > SSID.
Enter the following information and select OK:

Interface Name		example_wifi_if
Traffic Mode		Tunnel to Wireless Controller
IP/Network Mask		10.10.110.1/24
Administrative Access		Ping (to assist with testing)
DHCP Server		Enable
	Address Range	10.10.110.2 - 10.10.110.199
	Netmask	255.255.255.0
	Default Gateway	Same As Interface IP
	DNS Server	Same as System DNS
SSID		example_wifi
Security Mode		WPA2 Enterprise
Authentication		Local, select wlan_users user group.
Leave other settings at their default values.

To configure the SSID - CLI

config wireless-controller vap

edit example_wifi_if

set ssid "example_wifi"

set broadcast-ssid enable

set security wpa-enterprise

set auth usergroup

set usergroup wlan_users

set schedule always

end

config system interface

edit example_wifi_if

set ip 10.10.110.1 255.255.255.0

end

config system dhcp server

edit 0

set default-gateway 10.10.110.1

set dns-service default

set interface "example_wifi_if"

config ip-range

edit 1

set end-ip 10.10.110.199

set start-ip 10.10.110.2

end

set netmask 255.255.255.0

end

Adding the SSID to the FortiAP Profile

The radio portion of the FortiAP configuration is contained in the FortiAP Profile. By default, there is a profile for each platform (FortiAP model). You can create additional profiles if needed. The SSID needs to be specified in the profile.

To add the SSID to the FortiAP Profile - GUI

Go to WiFi and Switch Controller > FortiAP Profiles and edit the profile for your model of FortiAP unit.
In Radio 1 and Radio 2, add example_wifi in SSID.
Select OK.

Configuring security policies

A security policy is needed to enable WiFi users to access the Internet on port1. First you create firewall address for the WiFi network, then you create the example_wifi to port1 policy.

To create a firewall address for WiFi users - GUI

Go to Policy & Objects > Addresses.
Select Create New > Address, enter the following information and select OK.

Name	wlan_user_net
Type	IP/Netmask
Subnet / IP Range	10.10.110.0/24
Interface	example_wifi_if
Show in Address List	Enabled

To create a firewall address for WiFi users - CLI

config firewall address

edit "wlan_user_net"

set associated-interface "example_wifi_if"

set subnet 10.10.110.0 255.255.255.0

end

To create a security policy for WiFi users - GUI

Go to Policy & Objects > Firewall Policy and select Create New.
Enter the following information and select OK:

Incoming Interface	example_wifi_if
Source Address	wlan_user_net
Outgoing Interface	port1
Destination Address	All
Schedule	always
Service	ALL
Action	ACCEPT
NAT	ON. Select Use Destination Interface Address (default).
Leave other settings at their default values.

To create a firewall policy for WiFi users - CLI

config firewall policy

edit 0

set srcintf "example_wifi"

set dstintf "port1"

set srcaddr "wlan_user_net"

set dstaddr "all"

set schedule always

set service ALL

set action accept

set nat enable

end

Connecting the FortiAP units

You need to connect each FortiAP unit to the FortiGate unit, wait for it to be recognized, and then assign it to the AP Profile. But first, you must configure the interface to which the FortiAP units connect and the DHCP server that assigns their IP addresses.

In this example, the FortiAP units connect to port3 and are controlled through IP addresses on the 10.10.70.0/24 network.

To configure the interface for the AP unit - GUI

Go to Network > Interfaces, and edit the interface to which the AP unit connects (in this example, port3).
In Addressing mode, select Manual.
In IP/Network Mask, enter an IP address and netmask for the interface (in this example, 10.10.70.1/255.255.255.0).
In the Administrative Access section, go to IPv4 and select the Security Fabric Connection checkbox.
When FortiAP units are connected to the interface on FortiGate (directly or through a switch), you can go to the Edit Interface section and set the Role to LAN.

Selecting the LAN role loads the DHCP Server toggle. If you enable DHCP Server, the GUI can automatically set the DHCP IP range based on the interface IP address.
Click OK.

To configure the interface for the AP unit - CLI

config system interface

edit "port3"

set mode static

set ip 10.10.70.1 255.255.255.0

set allowaccess fabric

end

To configure the DHCP server for AP units - CLI

config system dhcp server

edit 3

set interface "port3"

config exclude-range

edit 1

set start-ip 10.10.70.1

set end-ip 10.10.70.1

end

config ip-range

edit 1

set start-ip 10.10.70.2

set end-ip 10.10.70.254

end

set default-gateway 10.10.70.1

set netmask 255.255.255.0

set vci-match enable

set vci-string "FortiAP"

end

To connect a FortiAP unit - GUI

Go to WiFi and Switch Controller > Managed FortiAPs.
Connect the FortiAP unit to port 3.
Periodically select Refresh while waiting for the FortiAP unit to be listed.
Recognition of the FortiAP unit can take up to two minutes.
If FortiAP units are connected but cannot be recognized, try disabling VCI-Match in the DHCP server settings.
When the FortiAP unit is listed, select the entry to edit it.
The Edit Managed Access Point window opens.
In State, select Authorize.
In FortiAP Profile, select the default profile for the FortiAP model.
Select OK.
Repeat Steps 2 through 7 for each FortiAP unit.

To connect a FortiAP unit - CLI

Connect the FortiAP unit to port 3.
Enter
config wireless-controller wtp
Wait 30 seconds, then enter get.
Retry the get command every 15 seconds or so until the unit is listed, like this:
== [ FAP22B3U10600118 ]
wtp-id: FAP22B3U10600118
Edit the discovered FortiAP unit like this:
edit FAP22B3U10600118
set admin enable
end
Repeat Steps 2 through 5 for each FortiAP unit.