interface
Use this command to edit the configuration of a FortiAnalyzer network interface.
Syntax
config system interface
edit <port_string>
set status {enable | disable}
set ip <ipv4address_mask>
set allowaccess {fgfm http https https-logging ping snmp soc-fabric ssh webservice}
set lldp {enable | disable}
set speed {1000full | 100full | 100half | 10full | 10half | auto}
set description <string>
set alias <string>
set mtu <integer>
set type {aggregate | vlan}
set interface <string>
set vlanid <integer>
set vlan-protocol {8021ad | 8021q}
config member
edit <interface-name>
end
set lacp-mode
set lacp-speed {fast | slow}
set min-links <integer>
set min-links-down {administrative | operational}
set link-up-delay <integer>
set aggregate
set camera-discovery {enable | disable}
config ipv6
set ip6-address <IPv6address prefix>
set ip6-allowaccess {fgfm http https https-logging ping snmp ssh webservice}
set ip6-autoconf {enable | disable}
end
end
|
Variable |
Description |
|---|---|
|
<port> |
The port can be set to a port number such as port1, port2, port3, or port4. Different FortiAnalyzer models have different numbers of ports. |
|
status {enable | disable} |
Enable/disable the interface (default = enable). If the interface is disabled it does not accept or send packets. If you disable a physical interface, VLAN interfaces associated with it are also disabled. |
|
ip <ipv4_mask> |
Enter the interface IPv4 address and netmask. The IPv4 address cannot be on the same subnet as any other interface. |
|
allowaccess {fgfm http https https-logging ping snmp soc-fabric ssh webservice} |
Enter the types of management access permitted on this interface. Separate multiple selected types with spaces. If you want to add or remove an option from the list, retype the list as required. |
|
lldp {enable | disable} |
Enable or disable the link layer discovery protocol (LLDP) (deafult = disable). |
|
speed {1000full 100full 100half 10full 10half auto} |
Enter the speed and duplexing the network port uses:
|
|
description <string> |
Enter a description of the interface (character limit = 63). |
|
alias <string> |
Enter an alias for the interface. |
|
mtu <integer> |
Set the maximum transportation unit (68 - 9000, default = 1500). |
|
type {aggregate | vlan} |
Set the type of interface (default = vlan). |
|
interface <string> |
Set the underling interface name for the VLAN interface. This option is only available if the |
|
vlanid <integer> |
Set the VLAN ID (1 - 4094, default = 0).This option is only available if the |
|
vlan-protocol {8021ad | 8021q} |
Set the ethernet protocol of the VLAN (IEEE 802.1AD or IEEE 802.1Q, default = IEEE 802.1Q). This option is only available if the |
|
member |
Physical interfaces that belong to the aggregate or the redundant interface. This option is only available if the |
|
lacp-mode |
Set the mode for LACP messages (default = active). This option is only available if the |
|
lacp-speed {fast | slow} |
Set how often the interface sends LACP messages:
This option is only available if the |
|
min-links <integer> |
Set the minimum number of aggregated ports that must be up (default = 1). This option is only available if the |
|
min-links-down {administrative | operational} |
Action to take when less than the configured minimum number of links are active:
This option is only available if the |
|
link-up-delay <integer> |
Set the number of milliseconds to wait before considering a link is up (default = 50). This option is only available if the |
|
aggregate |
|
|
camera-discovery {enable | disable} |
Enable/disable camera discovery (default = enable). This option is only available on hardware devices that support FortiRecorder. |
|
ipv6 |
IPv6 of the interface. |
|
Variables for |
|
|
<interface-name> |
Enter the interface name. |
|
Variables for |
|
|
ip6-address <ipv6 prefix> |
IPv6 address/prefix of interface. |
|
ip6-allowaccess {fgfm http https https-logging ping snmp ssh webservice} |
Allow management access to the interface. |
|
ip6-autoconf {enable | disable} |
Enable/disable address automatic configuration (SLAAC) (default = enable). |
Example
This example shows how to set the FortiAnalyzer port1 interface IPv4 address and network mask to 192.168.100.159 255.255.255.0, and the management access to ping, https, and ssh.
config system interface
edit port1
set allowaccess ping https ssh
set ip 192.168.110.26 255.255.255.0
set status up
end