Operational Guidelines
This section describes information related to the usage of FortiWLM.
This table lists the security modes supported for the Service Assurance Manager (SAM) on FortiWLM.
|
AP Models |
Security Modes |
|---|---|
|
All supported models |
Open |
|
WPA2 Enterprise AES |
|
|
WPA2 PSK AES |
|
|
Mixed PSK TKIP |
|
|
Mixed Enterprise TKIP |
The FortiWLC, FortiGate, and FortiWLM time must be synchronized. It is recommended to use NTP server.
FortiGate Scale Deployment
The following scale deployment limits apply to FortiGate-FortiWLM when the polling interval is set to 10 minutes.
|
Devices |
Maximum Limit |
||
|---|---|---|---|
|
|
FortiWLM-1000D |
FortiWLM-100D |
FWM-VM |
| FortiGate controllers | 5000 |
500 |
10000 |
| Access Points | 15000 |
2000 |
20000 |
| Stations | 100K |
20K |
150K |
The following scale deployment limits apply to FortiGate-FortiWLM when the polling interval is set to 1 minute.
|
Devices |
Maximum Limit |
||
|---|---|---|---|
|
|
FortiWLM-1000D |
FortiWLM-100D |
FWM-VM |
| FortiGate controllers |
1600 |
200 |
1600 |
| Access Points |
3200 |
400 |
3200 |
| Stations |
32K |
8000 |
32K |
The following are the hardware requirements for the aforementioned scale deployments.
|
Hardware Requirements |
||
|---|---|---|
|
FortiWLM-1000D |
FortiWLM-100D |
FWM-VM |
|
8 CPU/16 GB RAM/2 TB storage |
4 CPU/4 GB RAM/1TB storage |
8 CPU/16 GB RAM/2 TB storage |
FortiWLC Controllers
This following information is related to the usage of FortiWLM with FortiWLC controllers.
- In case of an Nplus1 cluster, note the following points:
- After the Nplus1 cluster formation is complete, it takes a maximum of 10 minutes to get discovered in FortiWLM.
- If the secondary and primary controllers are to work as standalone, then backup the FortiWLM configuration, double delete the controller and add it again from the controller inventory in FortiWLM, so that the controller can be successfully managed.
- The GUI menu option (Administration > System Settings > High Availability) to configure high availability from is removed for FortiWLM-100D.
- The risk level for Monitor > Overview > Application Summary cannot be defined for custom applications.
- [VPN with NPlus1] Configure the VPN client before configuring NPlus1 in secondary controller.
- Configure Jumbo frames from the controller only when the MTU values are to be more than 4500 bytes.
- Fortinet recommends usage of certificates with OCSP endpoint URI, when uploading certificates onto the WLM.
- Fortinet recommends running a single FortiWLM GUI session in scale setups.
FortiGate Controllers
This following information is related to the usage of FortiWLM with FortiGate controllers.
- A maximum of 5 concurrent GUI sessions are allowed.
- Application control is supported on FortiOS version 6.2.2 and later.
- Station activity logs are supported on FortiOS version 6.2.0 and later.
- Station logs from log storage as FortiCloud will fetch only 100 events at once.
- Wired clients are not supported.
|
Features |
FortiOS Versions | ||
|---|---|---|---|
|
6.2.2/6.2.3 |
6.4.0/6.4.1/6.4.2/6.4.3/6.4.4/ 6.4.5/6.4.6/6.4.7 |
7.0.0/7.0.1/7.0.2/7.0.3/7.0.5/7.2.0/7.2.1/7.2.2 |
|
| Dashboard Status |
|
|
|
| Application Control | ✓ | ✓ | ✓ |
|
Station Data |
✓ | ✓ | ✓ |
|
Station activity logs |
✓ | ✓ | ✓ |
|
|
|
|
|
|
AP Dashboard |
|
|
|
|
Retry % |
✓ | ✓ | ✓ |
|
Loss % |
✓ | ✓ | ✓ |
|
Channel Utilization% |
✓ | ✓ | ✓ |
|
SNR (dBm) |
✓ | ✓ | ✓ |
|
Average Throughput |
X | X |
✓ |
|
|
|
|
|
|
Station Dashboard |
|
|
|
|
Retry % |
✓ | ✓ | ✓ |
|
Loss % |
✓ | ✓ | ✓ |
|
Channel Utilization% |
X |
X |
X |
|
SNR (dBm) |
✓ |
✓ |
✓ |