Managing FortiSwitch units on VXLAN interfaces

You can use Virtual Extensible LAN (VXLAN) interfaces to create a layer-2 overlay network when managing a FortiSwitch unit over a layer-3 network. After a VXLAN tunnel is set up between a FortiGate device and a FortiSwitch unit, the FortiGate device can use the VXLAN interface to manage the FortiSwitch unit. Only the management traffic uses the VXLAN tunnel; the FortiSwitch data traffic does not go through the VXLAN tunnel to the FortiGate device.

In the following configuration example, the FG-500E device is connected with a VXLAN tunnel to the FS-524D unit. After FortiLink is enabled on the VXLAN interface, the FortiGate device can manage the FortiSwitch unit.

To manage the FortiSwitch unit with the VXLAN interface:

1. Configure the FortiSwitch unit.

2. Configure the FortiGate device.

Configure the FortiSwitch unit

1. Configure a VLAN to use as the VXLAN interface.

   config system interface

   edit "vlan-1000"

   set ip 10.200.1.2 255.255.255.0

   set allowaccess ping

   set vlanid 1000

   set interface "internal"

   next

   end

2. Configure the VXLAN interface with the remote IP address of the FortiGate device.

   config system vxlan

   edit "vx-4094"

   set vni 123456

   set vlanid 4094

   set interface "vlan-1000"

   set remote-ip "10.100.1.1"

   next

   end

3. Configure a static route with the VXLAN remote IP address as the destination.

   config router static

   edit 1

   set device "vlan-1000"

   set dst 10.100.1.1 255.255.255.255

   set gateway 10.200.1.50

   next

   end

4. Configure the switch trunk to make it static and disable the automatic VLAN provisioning.

   config switch trunk

   edit "__FoRtILnk0L3__"

   set auto-isl 1

   set static-isl enable

   set static-isl-auto-vlan disable

   set members "port19"

   next

   end

5. Configure the FortiLink interface to set the native VLAN to match the VLAN used for the VXLAN defined in step 1.

   config switch interface

   edit "__FoRtILnk0L3__"

   set native-vlan 1000

   set allowed-vlans 1,1000,4088-4094

   set dhcp-snooping trusted

   ....

   next

   end

6. If you are not using DHCP option 138 to inform the FortiSwitch unit of the FortiGate IP address, enable static discovery.

   config switch-controller global

   set ac-discovery-type static

   config ac-list

   edit 1

   set ipv4-address 10.255.2.1

   next

   end

   end

7. Assign VLAN ID 4094 to the “internal” interface, which will be used to establish the FortiLink connection with the FortiGate device over VXLAN.

   config switch interface

   edit "internal"

   set native-vlan 4094

   next

   end

8. Make certain that the FortiSwitch unit can be discovered by the FortiGate device over VXLAN.

   config switch global

   set auto-fortilink-discovery enable

   end

Configure the FortiGate device

1. Configure the system interface.

   config system interface

   edit "port2"

   set vdom "root"

   set ip 10.100.1.1 255.255.255.0

   set allowaccess ping https http

   next

   end

2. Configure the VXLAN interface.

   config system vxlan

   edit "flk-vxlan"

   set interface "port2"

   set vni 123456

   set remote-ip "10.200.1.2"

   next

   end

3. Configure the FortiLink interface as the VXLAN type and set the IP address.

   config system interface

   edit "flk-vxlan"

   set fortilink enable

   set ip 10.255.2.1 255.255.255.0

   next

   end

4. Configure a static route.

   config router static

   edit 0

   set dst 10.200.1.0 255.255.255.0

   set gateway 10.100.1.50

   set distance 5

   set device "port2"

   next

   end

5. Configure the DHCP server with option 138 to provide the switch-controller IP address to the FortiSwitch unit. DNS and NTP services are provided by the FortiGate device.

   config system dhcp server

   edit 0

   set dns-service local

   set ntp-service local

   set default-gateway 10.255.2.1

   set netmask 255.255.255.0

   set interface "flk-vxlan"

   config ip-range

   edit 1

   set start-ip 10.255.2.2

   set end-ip 10.255.2.254

   next

   end

   config options

   edit 1

   set code 138

   set type ip

   set ip "10.255.2.1"

   next

   end

   set vci-match enable

   set vci-string "FortiSwitch"

   next

   end

FortiSwitch VLANs over VXLAN

On some FortiSwitch models, you can send user traffic over a VXLAN tunnel, creating a layer-2 overlay over a layer-3 network, allowing Security Fabric functionality to be applied to devices connecting to the FortiSwitch unit.

In the following configuration example, the FG-1800F device is connected with a VXLAN tunnel to the FS-1048E unit. After FortiLink is enabled on the VXLAN interface, the FortiGate device can manage the FortiSwitch unit.

1. Configure a VLAN to use as the VXLAN interface.

   config system interface

   edit "vlan-1000"

   set ip 10.200.1.2 255.255.255.0

   set vlanid 1000

   set interface "internal"

   next

   end

2. Configure a static route with the VXLAN remote IP address as the destination.

   config router static

   edit 1

   set device "vlan-1000"

   set dst 10.100.1.1 255.255.255.255

   set gateway 10.200.1.50

   next

   end

3. Configure the link monitor to monitor access to the gateway.

   config system link-monitor

   edit "1"

   set srcintf "vlan-1000"

   set protocol ping

   set gateway-ip 10.200.1.50

   set interval 60

   next

   end

4. Configure the switch trunk to make it static and disable the automatic VLAN provisioning.

   config switch trunk

   edit "__FoRtILnk0L3__"

   set auto-isl 1

   set static-isl enable

   set static-isl-auto-vlan disable

   set members "port19"

   next

   end

5. Configure the FortiLink interface so that the native VLAN matches the VLAN used for the VXLAN defined in step 1.

   config switch interface

   edit "__FoRtILnk0L3__"

   set native-vlan 1000

   next

   end

6. Assign VLAN ID 4094 to the “internal” interface that will be used to establish the FortiLink connection with the FortiGate device over VXLAN.

   config switch interface

   edit "internal"

   set native-vlan 4094

   next

   end

7. If you are not using DHCP option 138 to inform the FortiSwitch unit of the FortiGate IP address, enable static discovery.

   config switch-controller global

   set ac-discovery-type static

   config ac-list

   edit 1

   set ipv4-address 10.255.2.1

   next

   end

   end

8. Connect two physical ports to each other as a loopback. In this example, port23 and port24 are connected.

9. Create two trunks, each trunk with one physical link that is connected as a loopback. In this example, trunk tr1 is created with port23 as a member. Trunk tr2 is created with port24 as a member. port24 forms a loopback with port23.

10. Configure trunk tr2 as static-isl. Leave the rest of the values at the defaults.

    config switch trunk

    edit "tr2"

    set auto-isl 1

    set static-isl enable

    set static-isl-auto-vlan disable

    set members "port24"

    next

    end

11. Configure the tr2 interface with a native VLAN of 4094 and the allowed VLANs as 1-4094.

    config switch interface

    edit "tr2"

    set native-vlan 4094

    set allowed-vlans 1-4094

    next

    end

12. Configure trunk tr1 as static-isl and static-isl-auto-vlan. Leave the rest of the values at the defaults. This trunk will be used in the VXLAN tunnel-loopback interface. port23 forms a loopback with port24.

    config switch trunk

    edit "tr1"

    set auto-isl 1

    set static-isl enable

    set static-isl-auto-vlan disable

    set members "port23"

    next

    end

13. Configure the tr1 interface with a native VLAN of 4087 and disable STP.

    config switch interface

    edit "tr1"

    set native-vlan 4087

    set stp-state disabled

    next

    end

14. Configure the VXLAN interface with tr1 as the tunnel-loopback interface. Set the interface to a normal SVI from step 1 to reach the Internet. The remote-ip address is the remote VTEP; in this case, the remote VTEP is the FortiGate interface being used for the VXLAN tunnel.

    With this configuration, all VLAN traffic from the switch, including all FortiSwitch VLANs, will loop to tr1 and initiate the VXLAN tunnel to the FortiGate device.

    config system vxlan

    edit vx1

    set interface vlan-1000

    set vni 4094

    set remote-ip 10.100.1.1

    set tunnel-loopback "tr1"

    next

    end