Dell Force10 Router and Switch

Support Added: FortiSIEM 4.7.2

Last Modification: FortiSIEM 6.4.0

Vendor Version Tested: Dell Force10 S4048T-ON

Vendor: Dell

Product Information: www.dell.com

• What is Discovered and Monitored
• Event Types
• Rules
• Reports
• Configuration
• Settings for Access Credentials

What is Discovered and Monitored

Protocol	Information Discovered	Metrics collected	Used for
SNMP (V1, V2c)	Host name, Serial number, Software version, Hardware model, Network interfaces, Hardware Components	Uptime, Network Interface metrics (utilization, bytes sent and received, packets sent and received, errors, discards and queue lengths), CPU utilization, Hardware Status	Availability and Performance Monitoring
Syslog			Security and Compliance
Telnet/SSH	Running and Startup configurations	Startup Configuration Change, Difference between Running and Startup configurations	Change monitoring

Event Types

In ADMIN > Device Support > Event Types, search for "force10" to see the event types associated with this device.

The following event types are available:

• Dell-Force10-IFMGR-OSTATE_DN

• Dell-Force10-IFMGR-OSTATE_UP

• Dell-Force10-SEC_LOGIN_SUCCESS

• Dell-Force10-FILEMGR-FILESAVED

• Dell-Force10-SEC_LOGIN_FAILURE

• Dell-Force10-TACACS_ACCESS_ACCEPTED

• Dell-Force10-SSH2-CONF

• Dell-Force10-SYS-CONFIG_I

Rules

There are no predefined rules for this device.

Reports

In RESOURCES > Rules, search for "force10" in the main content panel Search... field.

The following reports are available:

• Dell Force10 Interface Extended Performance Metrics

• Dell Force 10 Performance By Component

Configuration

• SNMP

• Syslog

• Telnet/SSH

SNMP

FortiSIEM uses SNMP to discover and monitor this device. Make sure SNMP is enabled for the device as directed in its product documentation. For more information, refer to sections "Discovery Settings" and "Setting Credentials" in the User Guide.

Syslog

FortiSIEM processes events from this device via syslog sent by the device. Configure the device to send syslog to FortiSIEM as directed in the device's product documentation, and FortiSIEM will parse the contents.

• For Syslog Server, or the server where the syslog should be sent, enter the IP address of your FortiSIEM virtual appliance.
• For Port, enter 514.

The syslog format should be the same as that shown in the example.

Example Syslog

Feb 11 09:50:21: %STKUNIT0-M:CP %IFMGR-5-OSTATE_UP: Changed interface state to up: Te 0/30
190>Jan 6 07:34:34: host1: %STKUNIT0-M:CP %ARPMGR-6-MAC_CHANGE: IP-4-ADDRMOVE: IP address 10.1.48.14 is moved from MAC address 52:54:00:16:5a:74  to MAC address 52:54:00:22:c7:81 .
<189>Jan 4 08:08:43: host1: %STKUNIT0-M:CP %SEC-5-LOGIN_SUCCESS: Login successful for user user1 on line vty0 ( 10.1.48.201 )
>110>1 2017-01-09T15:41:53.191+08:00 p01-ctl-sw2-d5c2f1 - SEC LOGOUT - INFO: Exec session is terminated for user user2 on line vty0 ( 192.168.128.202 )
Feb 11 08:36:21 utc: %STKUNIT0-M:CP %IFMGR-5-OSTATE_DN: Changed interface state to down: Te 0/31

Telnet/SSH

FortiSIEM uses Telnet/SSH to communicate with this device. Refer to the product documentation for your device to enable Telnet/SSH.

These commands are used for discovery and performance monitoring via SSH. Please make sure that the access credentials you provide in FortiSIEM have the permissions necessary to execute these commands on the device. To initiate discovery and monitoring of your device over this protocol, refer to sections "Discovery Settings" and "Setting Credentials" in the User Guide.

• show startup-config
• show running-config
• show version
• show ip route
• enable
• terminal pager 0

Settings for Access Credentials

• SNMP Access Credentials for All Devices

• Telnet Access Credentials for All Devices

• SSH Access Credentials for All Devices

SNMP Access Credentials for All Devices

Set these Access Method Definition values to allow FortiSIEM to communicate with your device over SNMP. Set the Name and Community String.

Setting	Value
Name	<set name>
Device Type	Generic
Access Protocol	SNMP
Community String	<your own>

Telnet Access Credentials for All Devices

These are the generic settings for providing Telnet access to your device from FortiSIEM

Setting	Value
Name	Telnet-generic
Device Type	generic
Access Protocol	Telnet
Port	23
User Name	A user who has permission to access the device over Telnet
Password	The password associated with the user

SSH Access Credentials for All Devices

These are the generic settings for providing SSH access to your device from FortiSIEM.

Setting	Value
Name	ssh-generic
Device Type	Generic
Access Protocol	SSH
Port	22
User Name	A user who has access credentials for your device over SSH
Password	The password for the user