Brocade ServerIron ADX

• What is Discovered and Monitored
• Event Types
• Rules
• Reports
• Configuration
• Settings for Access Credentials

What is Discovered and Monitored

Protocol	Information discovered	Metrics/Logs collected	Used for
SNMP	Host name, serial number, hardware (CPU, memory, network interface etc)	Uptime, CPU, Memory, Interface Utilization, Hardware status, Real Server Statistics	Performance/Availability Monitoring

Event Types

• PH_DEV_MON_SYS_CPU_UTIL

  [PH_DEV_MON_SYS_CPU_UTIL]:[eventSeverity]=PHL_INFO,[fileName]=deviceBrocadeServerIron.cpp,[lineNumber]=434,[cpuName]=CPU,[hostName]=lb1-1008-qts,[hostIpAddr]=192.0.2.15,[cpuUtil]=55.000000,[pollIntv]=176,[phLogDetail]=

• PH_DEV_MON_SYS_MEM_UTIL

  [PH_DEV_MON_SYS_MEM_UTIL]:[eventSeverity]=PHL_INFO,[fileName]=deviceBrocadeServerIron.cpp,[lineNumber]=456,[memName]=Physical
  Memory,[hostName]=lb1-1008-qts,[hostIpAddr]=192.0.2.15,[memUtil]=10.000000,[pollIntv]=176,[phLogDetail]=

• PH_DEV_MON_NET_INTF_UTIL

  [PH_DEV_MON_NET_INTF_UTIL]:[eventSeverity]=PHL_INFO,[fileName]=phIntfFilter.cpp,[lineNumber]=323,[intfName]=GigabitEthernet8,[intfAlias]=,[hostName]=lb1-1008-qts,[hostIpAddr]=192.0.2.15,[pollIntv]=56,[recvBytes64]=1000000,[recvBitsPerSec]=142857.142857,[inIntfUtil]=0.014286,[sentBytes64]=2000000,[sentBitsPerSec]=285714.285714,[outIntfUtil]=0.028571,[recvPkts64]=0,[sentPkts64]=0,[inIntfPktErr]=0,[inIntfPktErrPct]=0.000000,[outIntfPktErr]=0,[outIntfPktErrPct]=0.000000,[inIntfPktDiscarded]=0,[inIntfPktDiscardedPct]=0.000000,[outIntfPktDiscarded]=0,[outIntfPktDiscardedPct]=0.000000,[outQLen64]=0,[intfInSpeed64]=1000000000,[intfOutSpeed64]=1000000000,[intfAdminStatus]=up,[intfOperStatus]=up,[daysSinceLastUse]=0,[totIntfPktErr]=0,[totBitsPerSec]=428571.428571,[phLogDetail]=
  
  

• PH_DEV_MON_SERVERIRON_REAL_SERVER_STAT

   [PH_DEV_MON_SERVERIRON_REAL_SERVER_STAT]:[eventSeverity]=PHL_INFO,[fileName]=deviceBrocadeServerIron.cpp,[lineNumber]=507,[hostName]=lb1-1008-qts,[hostIpAddr]=192.0.2.15,[realServerIpAddr]=192.0.2.131,[realServerState]=7,[failedPortExists]=2,[openConnectionsCount]=2,[peakConns]=114,[activeSessions]=4,[phLogDetail]=

• PH_DEV_MON_HW_STATUS

  [PH_DEV_MON_HW_STATUS]:[eventSeverity]=PHL_INFO,[fileName]=deviceBrocadeServerIron.cpp,[lineNumber]=359,[hostName]=lb1-1008-qts,[hostIpAddr]=192.0.2.15,[hwStatusCode]=2,[hwPowerSupplyStatus]=0,[hwTempSensorStatus]=2,[hwFanStatus]=0,[phLogDetail]=
  
  [PH_DEV_MON_HW_STATUS_TEMP_CRIT]:[eventSeverity]=PHL_CRITICAL,[fileName]=device.cpp,[lineNumber]=13812,[hostName]=lb1-1008-qts,[hostIpAddr]=192.0.2.15,[hwStatusCode]=2,[hwComponentName]=1-Temperature
  sensor,[hwComponentStatus]=Critical,[phLogDetail]=

• PH_DEV_MON_HW_TEMP

   [PH_DEV_MON_HW_TEMP]:[eventSeverity]=PHL_INFO,[fileName]=deviceBrocadeServerIron.cpp,[lineNumber]=401,[hostName]=lb1-1008-qts,[hostIpAddr]=192.0.2.15,[hwComponentName]=Temp1,[envTempDegF]=90,[phLogDetail]=

Rules

There are no predefined rules for this device other than covered by generic network devices.

Reports

There are no predefined reports for this device other than covered by generic network devices.

Configuration

SNMP

FortiSIEM uses SNMP to discover and monitor this device. Make sure SNMP is enabled for the device as directed in its product documentation. For more information, refer to sections "Discovery Settings" and "Setting Credentials" in the User Guide.

Settings for Access Credentials

Use these Access Method Definition settings to allow FortiSIEM to access your device.

Setting	Value
Name	<set name>
Device Type	Brocade ServerIron ADX
Access Protocol	See Access Credentials
Port	See Access Credentials
Password config	See Password Configuration