CLI scripts

CLI scripts include only FortiOS CLI commands as they are entered at the command line prompt on a FortiGate device. CLI scripts do not include Tool Command Language (Tcl) commands, and the first line of the script is not “#!” as it is for Tcl scripts.

CLI scripts are useful for specific tasks such as configuring a routing table, adding new firewall policies, or getting system information. These example tasks easily apply to any or all FortiGate devices connected to the FortiManager system.

However, the more complex a CLI script becomes the less it can be used with all FortiGate devices - it quickly becomes tied to one particular device or configuration. One example of this is any script that includes the specific IP address of a FortiGate device’s interfaces cannot be executed on a different FortiGate device.

Samples of CLI scripts have been included to help get you started writing your own scripts for your network administration tasks.

Error messages will help you determine the causes of any CLI scripting problems, and fix them. For more information, see Error Messages.

The troubleshooting tips section provides some suggestions on how to quickly locate and fix problems in your CLI scripts. For more information, see Troubleshooting Tips.

CLI script samples

There are two types of CLI scripts. The first type is getting information from your FortiGate device. The second type is changing information on your FortiGate device.

Getting information remotely is one of the main purposes of your FortiManager system, and CLI scripts allow you to access any information on your FortiGate devices. Getting information typically involves only one line of script as the following scripts show.

To view interface information for port1:
Script	show system interface port1
Output	config system interface edit "port1" set vdom "root" set ip 172.20.120.148 255.255.255.0 set allowaccess ping https ssh set type physical next end
Variations	Remove the interface name to see a list that includes all the interfaces on the FortiGate device including virtual interfaces such as VLANs.
Note	This script does not work when run on a policy package.
	If the preceding script is used to be run on the FortiGate Directly (via CLI) or run on device database on a FortiGate has the VDOM enabled. The script will have be modified to the following: config global show system interface port1 end
	Since running on device database does not yield any useful information. View the log of script running on device: FortiGate-VM64-70 ------- Executing time: 2013-10-15 13:27:32 ------ Starting log (Run on database) config global end Running script on DB success ------- The end of log ----------
	The script should be run on the FortiGate Directly (via CLI). View the log of script running on device: FortiGate-VM64-70 ------- Executing time: 2013-10-15 13:52:02 ------ Starting log (Run on device) FortiGate-VM64 $ config global FortiGate-VM64 (global) $ show system interface port1 config system interface edit "port1" set vdom "root" set ip 10.2.66.181 255.255.0.0 set allowaccess ping https ssh snmp http telnet fgfm auto-ipsec radius-acct probe-response capwap set type physical set snmp-index 1 next end FortiGate-VM64 (global) $ end ------- The end of log ----------
	To view the entries in the static routing table. To get any useful information, the script has to be re-written for the following if the VDOM is enabled for FortiGate and has to be run on the FortiGate Directly (via CLI). config vdom edit root show route static next end
	Here is a sample run of the preceding script running on the FortiGate Directly (via CLI). View the log of script running on device: FortiGate-VM64-70 ------- Executing time: 2013-10-15 14:24:10 ------ Starting log (Run on device) FortiGate-VM64 $ config vdom FortiGate-VM64 (vdom) $ edit root current vf=root:0 FortiGate-VM64 (root) $ show route static config router static edit 1 set device "port1" set gateway 10.2.0.250 next end FortiGate-VM64 (root) $ next FortiGate-VM64 (vdom) $ end ------- The end of log ----------

To view the entries in the static routing table:
Script	show route static
Output	config router static edit 1 set device "port1" set gateway 172.20.120.2 next edit 2 set device "port2" set distance 7 set dst 172.20.120.0 255.255.255.0 set gateway 172.20.120.2 next end
Variations	none

View information about all the configured FDN servers on this device:
Script	config global diag debug rating end
Output	View the log of script running on device: FortiGate-VM64 ------- Executing time: 2013-10-15 14:32:15 ------ Starting log (Run on device) FortiGate-VM64 $ config global FortiGate-VM64 (global) $ diagnose debug rating Locale : english License : Contract Expiration : Thu Jan 3 17:00:00 2030 -=- Server List (Tue Oct 15 14:32:49 2013) -=- IP Weight RTT Flags TZ Packets Curr Lost Total Lost 192.168.100.206 35 2 DIF -8 4068 72 305 192.168.100.188 36 2 F -8 4052 72 308 FortiGate-VM64 (global) $ end ------- The end of log ----------
Variations	Output for this script will vary based on the state of the FortiGate device. The preceding output is for a FortiGate device that has never been registered. For a registered FortiGate device without a valid license, the output would be similar to: Locale : english License : Unknown Expiration : N/A Hostname : guard.fortinet.net -=- Server List (Tue Oct 3 09:34:46 2006) -=- IP Weight Round-time TZ Packets Curr Lost Total Lost ** None **

Setting FortiGate device information with CLI scripts gives you access to more settings and allows you more fine grained control than you may have in the Device Manager. Also CLI commands allow access to more advanced options that are not available in the FortiGate GUI. Scripts that set information require more lines.

Any scripts that you will be running on the global database must include the full CLI commands and not use short forms for the commands. Short form commands will not run on the global database.

Create a new account profile called policy_admin allowing read-only access to policy related areas:
Script	config global config system accprofile edit "policy_admin" set fwgrp read set loggrp read set sysgrp read next end end
Output	View the log of script running on device:FortiGate-VM64 ------- Executing time: 2013-10-16 13:39:35 ------ Starting log (Run on device) FortiGate-VM64 $ config global FortiGate-VM64 (global) $ config system accprofile FortiGate-VM64 (accprofile) $ edit "prof_admin" FortiGate-VM64 (prof_admin) $ set fwgrp read FortiGate-VM64 (prof_admin) $ set loggrp read FortiGate-VM64 (prof_admin) $ set sysgrp read FortiGate-VM64 (prof_admin) $ next FortiGate-VM64 (accprofile) $ end FortiGate-VM64 (global) $ end ------- The end of log ----------
Variations	This profile is read-only to allow a policy administrator to monitor this device’s configuration and traffic. Variations may include enabling other areas as read-only or write permissions based on that account type’s needs.

With the introduction of global objects/security console (global database), you can run a CLI script on the FortiManager global database in addition to running it on a FortiGate unit directly. Compare the following sample scripts:

• Running a CLI script on a FortiGate unit

  config vdom

  edit “root”

  config firewall policy

  edit 10

  set srcintf “port5”

  set dstintf “port6”

  set srcaddr “all”

  set dstaddr “all”

  set status disable

  set schedule "always"

  set service "ALL"

  set logtraffic disable

  next

  end

• Running a CLI script on the global database

  config firewall policy

  edit 10

  set srcintf “port5”

  set dstintf “port6”

  set srcaddr "all"

  set dstaddr "all"

  set status disable

  set schedule "always"

  set service "ALL"

  set logtraffic disable

  next

  end

Error Messages

Most error messages you will see are regular FortiGate CLI error messages. If you are familiar with the CLI you will likely recognize them.

Other error messages indicate your script encountered problems while executing, such as:

• command parse error: It was not possible to parse this line of your script into a valid FortiGate CLI command. Common causes for this are misspelled keywords or an incorrect command format.
• unknown action: Generally this message indicates the previous line of the script was not executed, especially if the previous line accesses an object such as “config router static”.
• Device XXX failed-1: This usually means there is a problem with the end of the script. XXX is the name of the FortiGate unit the script is to be executed on. If a script has no end statement or that line has an error in it you may see this error message. You may also see this message if the FortiGate unit has not been synchronized by deploying its current configuration.

Troubleshooting Tips

Here are some troubleshooting tips to help locate and fix problems you may experience with your scripts.

• Check the script output. Generally the error messages displayed here will help you locate and fix the problem.
• See the FortiGate CLI Reference for more information on all CLI commands.
• There is a limit to the number of scripts allowed on the FortiManager unit. Try removing an old script before trying to save your current one.
• As mentioned at the start of this chapter, ensure the console more command is disabled on the FortiGate devices where scripts execute. Otherwise a condition may occur where both the FortiGate device and the FortiManager system are waiting for each other to respond until they timeout.
• There should be no punctuation at the start or end of the lines.
• Only whitespace is allowed on the same line as the command. This is useful in lining up end and next commands for quick and easy debugging of the script.
• Keep your scripts short. They are easier to troubleshoot and it gives you more flexibility. You can easily execute a number of scripts after each other.
• Use full command names. For example instead of “set host test” use “set hostname test”. This is required for any scripts that are to be run on the global database.
• Use the number sign (#) to comment out a line you suspect contains an error.