Troubleshooting

Use the following commands to verify that IPsec VPN sessions are up and running.

Use the diagnose load-balance status command from the management board to determine the primary FPC. The third line of the command output shows which FPC is operating as the primary FPC.

diagnose load-balance status
==========================================================================
MBD SN: F6KF313E17900032
  Primary FPC Blade: slot-5
 
     Slot  1: FPC6KF3E17900200
       Status:Working   Function:Active 
       Link:      Base: Up          Fabric: Up  
       Heartbeat: Management: Good   Data: Good  
       Status Message:"Running"
     Slot  2: FPC6KF3E17900201
       Status:Working   Function:Active 
       Link:      Base: Up          Fabric: Up  
       Heartbeat: Management: Good   Data: Good  
       Status Message:"Running"
     Slot  3: FPC6KF3E17900207
       Status:Working   Function:Active 
       Link:      Base: Up          Fabric: Up  
       Heartbeat: Management: Good   Data: Good 
       Status Message:"Running"
     Slot  4: FPC6KF3E17900219
       Status:Working   Function:Active 
       Link:      Base: Up          Fabric: Up  
       Heartbeat: Management: Good   Data: Good  
       Status Message:"Running"
     Slot  5: FPC6KF3E17900235
       Status:Working   Function:Active 
       Link:      Base: Up          Fabric: Up  
       Heartbeat: Management: Good   Data: Good  
       Status Message:"Running"
     Slot  6: FPC6KF3E17900169
       Status:Working   Function:Active 
       Link:      Base: Up          Fabric: Up
       Heartbeat: Management: Good   Data: Good  
       Status Message:"Running"

Log into the primary FPC CLI and run the command diagnose vpn tunnel list <phase2-name> to show the sessions for the phase 2 configuration. The example below is for the to-fgt2 phase 2 configuration configured previously in this chapter. The command output shows the security association (SA) setup for this phase 2 and the all of the destination subnets .

From the command output, make sure the SA is installed and the dst addresses are correct.

diagnose vpn tunnel list name to-fgt2
list ipsec tunnel by names in vd 11
------------------------------------------------------
name=to-fgt2 ver=1 serial=2 4.2.0.1:0->4.2.0.2:0
bound_if=199 lgwy=static/1 tun=intf/0 mode=auto/1 encap=none/40 options[0028]=npu ike_assit 
proxyid_num=1 child_num=0 refcnt=8581 ilast=0 olast=0 auto-discovery=0
ike_asssit_last_sent=4318202512
stat: rxp=142020528 txp=147843214 rxb=16537003048 txb=11392723577
dpd: mode=on-demand on=1 idle=20000ms retry=3 count=0 seqno=2
natt: mode=none draft=0 interval=0 remote_port=0
proxyid=to-fgt2 proto=0 sa=1 ref=8560 serial=8
  src: 0:4.2.1.0/255.255.255.0:0 0:4.2.2.0/255.255.255.0:0
  dst: 0:4.2.3.0/255.255.255.0:0 0:4.2.4.0/255.255.255.0:0 0:4.2.5.0/255.255.255.0:0SA: ref=7 options=22e type=00 soft=0 mtu=9134 expire=42819/0B replaywin=2048 seqno=4a26f esn=0 replaywin_lastseq=00045e80
  life: type=01 bytes=0/0 timeout=43148/43200
  dec: spi=e89caf36 esp=aes key=16 26aa75c19207d423d14fd6fef2de3bcf
       ah=sha1 key=20 7d1a330af33fa914c45b80c1c96eafaf2d263ce7
  enc: spi=b721b907 esp=aes key=16 acb75d21c74eabc58f52ba96ee95587f
       ah=sha1 key=20 41120083d27eb1d3c5c5e464d0a36f27b78a0f5a
  dec:pkts/bytes=286338/40910978, enc:pkts/bytes=562327/62082855
  npu_flag=03 npu_rgwy=4.2.0.2 npu_lgwy=4.2.0.1 npu_selid=b dec_npuid=3 enc_npuid=1

Log into the CLI of any of the FPCs and run the command diagnose test application fctrlproxyd 2. The output should show matching destination subnets.

diagnose test application fctrlproxyd 2 

fcp route dump : last_update_time 24107 

Slot:4
	routecache entry: (5)
	checksum:27 AE 00 EA 10 8D 22 0C D6 48 AB 2E 7E 83 9D 24 
	vd:3 p1:to-fgt2 p2:to-fgt2 subnet:4.2.3.0 mask:255.255.255.0 enable:1 
	vd:3 p1:to-fgt2 p2:to-fgt2 subnet:4.2.4.0 mask:255.255.255.0 enable:1 
	vd:3 p1:to-fgt2 p2:to-fgt2 subnet:4.2.5.0 mask:255.255.255.0 enable:1 
	=========================================