ADVPN with BGP as the routing protocol

This is a sample configuration of ADVPN with BGP as the routing protocol. The following options must be enabled for this configuration:

• On the hub FortiGate, IPsec phase1-interface net-device disable must be run.

• IBGP must be used between the hub and spoke FortiGates.

• bgp neighbor-group/neighbor-range must be reused.

To configure ADVPN with BGP as the routing protocol using the CLI:

1. Configure hub FortiGate WAN interface, internal interface, and a static route:

   config system interface
       edit "port9"
           set alias "WAN"
           set ip 22.1.1.1 255.255.255.0
       next
       edit "port10"
           set alias "Internal"
           set ip 172.16.101.1 255.255.255.0
       next
   end   
   config router static
       edit 1
           set gateway 22.1.1.2
           set device "port9"
       next  
   end  		

2. Configure the hub FortiGate:

   1. Configure the hub FortiGate IPsec phase1-interface and phase2-interface:

      config vpn ipsec phase1-interface
          edit "advpn-hub"
              set type dynamic
              set interface "port9"
              set peertype any
              set net-device disable
              set proposal aes128-sha256 aes256-sha256 3des-sha256 aes128-sha1 aes256-sha1 3des-sha1
              set add-route disable
              set dpd on-idle
              set auto-discovery-sender enable
              set psksecret sample
              set dpd-retryinterval 5
          next
      end
      config vpn ipsec phase2-interface
          edit "advpn-hub"
              set phase1name "advpn-hub"
              set proposal aes128-sha1 aes256-sha1 3des-sha1 aes128-sha256 aes256-sha256 3des-sha256
          next
      end

      When net-device is disabled, a tunnel ID is generated for each dynamic tunnel. This ID, in the form of an IP address, is used as the gateway in the route entry to that tunnel. The tunnel-search option is removed in FortiOS 7.0.0 and later.

   2. Configure the hub FortiGate firewall policy:

      config firewall policy
          edit 1
              set name "spoke2hub"
              set srcintf "advpn-hub"
              set dstintf "port10"
              set srcaddr "all"
              set dstaddr "172.16.101.0"
              set action accept
              set schedule "always"
              set service "ALL"
          next
          edit 2
              set name "spoke2spoke"
              set srcintf "advpn-hub"
              set dstintf "advpn-hub"
              set srcaddr "all"
              set dstaddr "all"
              set action accept
              set schedule "always"
              set service "ALL"
          next
      end   

   3. Configure the hub FortiGate's IPsec tunnel interface IP address:

      config system interface
          edit "advpn-hub1"
              set ip 10.10.10.254 255.255.255.255
              set remote-ip 10.10.10.253 255.255.255.0
          next
      end

   4. Configure the hub FortiGate's BGP:

      config router bgp
          set as 65412
          config neighbor-group
              edit "advpn"
                  set link-down-failover enable
                  set remote-as 65412
                  set route-reflector-client enable
              next
          end
          config neighbor-range
              edit 1
                  set prefix 10.10.10.0 255.255.255.0
                  set neighbor-group "advpn"
              next
          end
          config network
              edit 1
                  set prefix 172.16.101.0 255.255.255.0
              next
          end
      end

3. Configure the spoke FortiGates:

   1. Configure the spoke FortiGates' WAN, internal interfaces, and static routes:

      1. Configure Spoke1:

         config system interface
             edit "wan1"
                 set alias "primary_WAN"
                 set ip 15.1.1.2 255.255.255.0
             next
             edit "wan2"
                 set alias "secondary_WAN"
                 set ip 12.1.1.2 255.255.255.0
             next
             edit "internal"
                 set ip 10.1.100.1 255.255.255.0
             next
         end 
         config router static
             edit 1
                 set gateway 12.1.1.1
                 set device "wan2"
                 set distance 15        
             next
             edit 2
                 set gateway 15.1.1.1
                 set device "wan1"
             next
         end

      2. Configure the Spoke2:

         config system interface
             edit "wan1"
                 set alias "primary_WAN"
                 set ip 13.1.1.2 255.255.255.0
             next
             edit "wan2"
                 set alias "secondary_WAN"
                 set ip 17.1.1.2 255.255.255.0
             next
             edit "internal"
                 set ip 192.168.4.1 255.255.255.0
             next
         end 
         config router static
             edit 1
                 set gateway 17.1.1.1
                 set device "wan2"
                 set distance 15        
             next
             edit 2
                 set gateway 13.1.1.1
                 set device "wan1"
             next
         end

   2. Configure the spoke FortiGates' IPsec phase1-interface and phase2-interface:

      1. Configure Spoke1:

         config vpn ipsec phase1-interface
             edit "spoke1"
                 set interface "wan1"
                 set peertype any
                 set net-device enable
                 set proposal aes128-sha256 aes256-sha256 aes128-sha1 aes256-sha1
                 set add-route disable
                 set dpd on-idle
                 set auto-discovery-receiver enable
                 set remote-gw 22.1.1.1
                 set psksecret sample 
                 set dpd-retryinterval 5
             next
             edit "spoke1_backup"
                 set interface "wan2"
                 set peertype any
                 set net-device enable
                 set proposal aes128-sha256 aes256-sha256 aes128-sha1 aes256-sha1
                 set add-route disable
                 set dpd on-idle
                 set auto-discovery-receiver enable
                 set remote-gw 22.1.1.1
                 set monitor "spoke1"
                 set psksecret sample
                 set dpd-retryinterval 5
             next    
         end
         config vpn ipsec phase2-interface
             edit "spoke1"
                 set phase1name "spoke1"
                 set proposal aes128-sha1 aes256-sha1 aes128-sha256 aes256-sha256 aes128gcm aes256gcm chacha20poly1305
                 set auto-negotiate enable
             next
             edit "spoke1_backup"
                 set phase1name "spoke1_backup"
                 set proposal aes128-sha1 aes256-sha1 aes128-sha256 aes256-sha256 aes128gcm aes256gcm chacha20poly1305
                 set auto-negotiate enable
             next  
         end

      2. Configure Spoke2:

         config vpn ipsec phase1-interface
             edit "spoke2"
                 set interface "wan1"
                 set peertype any
                 set net-device enable
                 set proposal aes128-sha256 aes256-sha256 aes128-sha1 aes256-sha1
                 set add-route disable
                 set dpd on-idle
                 set auto-discovery-receiver enable
                 set remote-gw 22.1.1.1
                 set psksecret sample 
                 set dpd-retryinterval 5
             next
             edit "spoke2_backup"
                 set interface "wan2"
                 set peertype any
                 set net-device enable
                 set proposal aes128-sha256 aes256-sha256 aes128-sha1 aes256-sha1
                 set add-route disable
                 set dpd on-idle
                 set auto-discovery-receiver enable
                 set remote-gw 22.1.1.1
                 set monitor "spoke2"
                 set psksecret sample
                 set dpd-retryinterval 5
             next    
         end
         config vpn ipsec phase2-interface
             edit "spoke2"
                 set phase1name "spoke2"
                 set proposal aes128-sha1 aes256-sha1 aes128-sha256 aes256-sha256 aes128gcm aes256gcm chacha20poly1305
                 set auto-negotiate enable
             next
             edit "spoke2_backup"
                 set phase1name "spoke2_backup"
                 set proposal aes128-sha1 aes256-sha1 aes128-sha256 aes256-sha256 aes128gcm aes256gcm chacha20poly1305
                 set auto-negotiate enable
             next  
         end

   3. Configure the spoke FortiGates' firewall policies:

      1. Configure Spoke1:

         config firewall policy
             edit 1
                 set name "outbound_advpn"
                 set srcintf "internal"
                 set dstintf "spoke1" "spoke1_backup"
                 set srcaddr "all"
                 set dstaddr "all"
                 set action accept
                 set schedule "always"
                 set service "ALL"
             next
             edit 2
                 set name "inbound_advpn"
                 set srcintf "spoke1" "spoke1_backup"
                 set dstintf "internal"
                 set srcaddr "all"
                 set dstaddr "all"
                 set action accept
                 set schedule "always"
                 set service "ALL"
             next
         end

      2. Configure Spoke2:

         config firewall policy
             edit 1
                 set name "outbound_advpn"
                 set srcintf "internal"
                 set dstintf "spoke2" "spoke2_backup"
                 set srcaddr "all"
                 set dstaddr "all"
                 set action accept
                 set schedule "always"
                 set service "ALL"
             next
             edit 2
                 set name "inbound_advpn"
                 set srcintf "spoke2" "spoke2_backup"
                 set dstintf "internal"
                 set srcaddr "all"
                 set dstaddr "all"
                 set action accept
                 set schedule "always"
                 set service "ALL"
             next
         end

   4. Configure the spoke FortiGates' tunnel interface IP addresses:

      1. Configure Spoke1:

         config system interface
             edit "spoke1"
                 set ip 10.10.10.1 255.255.255.255
                 set remote-ip 10.10.10.254 255.255.255.0
             next
             edit "spoke1_backup"
                 set ip 10.10.10.2 255.255.255.255
                 set remote-ip 10.10.10.254 255.255.255.0
             next    
         end

      2. Configure Spoke2:

         config system interface
             edit "spoke2"
                 set ip 10.10.10.3 255.255.255.255
                 set remote-ip 10.10.10.254 255.255.255.0
             next
             edit "spoke2_backup"
                 set ip 10.10.10.4 255.255.255.255
                 set remote-ip 10.10.10.254 255.255.255.0
             next    
         end

   5. Configure the spoke FortiGates' BGP:

      1. Configure Spoke1:

         config router bgp
             set as 65412
             config neighbor
                 edit "10.10.10.254"
                     set advertisement-interval 1
                     set link-down-failover enable
                     set remote-as 65412
                 next
             end
             config network
                 edit 1
                     set prefix 10.1.100.0 255.255.255.0
                 next
             end
         end

      2. Configure Spoke2:

         config router bgp
             set as 65412
             config neighbor
                 edit "10.10.10.254"
                     set advertisement-interval 1
                     set link-down-failover enable
                     set remote-as 65412
                 next
             end
             config network
                 edit 1
                     set prefix 192.168.4.0 255.255.255.0
                 next
             end
         end

4. Run diagnose and get commands on Spoke1 to check VPN and BGP states:

   1. Run the diagnose vpn tunnel list command on Spoke1. The system should return the following:

      list all ipsec tunnel in vd 0
      ----
      name=spoke1 ver=1 serial=2 15.1.1.2:0->22.1.1.1:0 tun_id=22.1.1.1
      bound_if=7 lgwy=static/1 tun=intf/0 mode=auto/1 encap=none/536 options[0218]=npu create_dev frag-rfc  accept_traffic=1
      
      proxyid_num=1 child_num=1 refcnt=19 ilast=1 olast=1 ad=r/2
      stat: rxp=1 txp=160 rxb=16428 txb=8969
      dpd: mode=on-idle on=1 idle=5000ms retry=3 count=0 seqno=628
      natt: mode=none draft=0 interval=0 remote_port=0
      proxyid=spoke1 proto=0 sa=1 ref=6 serial=1 auto-negotiate adr
        src: 0:0.0.0.0/0.0.0.0:0
        dst: 0:0.0.0.0/0.0.0.0:0
        SA:  ref=6 options=1a227 type=00 soft=0 mtu=1438 expire=1225/0B replaywin=1024
             seqno=a1 esn=0 replaywin_lastseq=00000002 itn=0
        life: type=01 bytes=0/0 timeout=2369/2400
        dec: spi=c53a8f5b esp=aes key=16 cbe88682ad896a69290027b6dd8f7162
             ah=sha1 key=20 7bb704b388f83783ac76c2ab0b6c9f7dcf78e93b
        enc: spi=6e3633fc esp=aes key=16 1a0da3f4deed3d16becc9dda57537355
             ah=sha1 key=20 368544044bd9b82592d72476ff93d5055056da8d
        dec:pkts/bytes=1/16364, enc:pkts/bytes=160/19168
        npu_flag=03 npu_rgwy=22.1.1.1 npu_lgwy=15.1.1.2 npu_selid=1 dec_npuid=1 enc_npuid=1
      ----
      name=spoke1_backup ver=1 serial=1 12.1.1.2:0->22.1.1.1:0 tun_id=22.1.1.1
      bound_if=6 lgwy=static/1 tun=intf/0 mode=auto/1 encap=none/536 options[0218]=npu create_dev frag-rfc  accept_traffic=0
      
      proxyid_num=1 child_num=0 refcnt=11 ilast=0 olast=0 ad=/0
      stat: rxp=0 txp=0 rxb=0 txb=0
      dpd: mode=on-idle on=0 idle=5000ms retry=3 count=0 seqno=0
      natt: mode=none draft=0 interval=0 remote_port=0
      proxyid=spoke1_backup proto=0 sa=0 ref=2 serial=1 auto-negotiate adr
        src: 0:0.0.0.0/0.0.0.0:0
        dst: 0:0.0.0.0/0.0.0.0:0

   2. Run the get router info bgp summary command on Spoke1. The system should return the following:

      BGP router identifier 7.7.7.7, local AS number 65412
      BGP table version is 2
      1 BGP AS-PATH entries
      0 BGP community entries
      
      Neighbor             V         AS [[QualityAssurance62/MsgRcvd]] [[QualityAssurance62/MsgSent]]   [[QualityAssurance62/TblVer]]  InQ OutQ Up/Down  State/PfxRcd
      10.10.10.254       1.          65412     143     142         1.     1.     1. 00:24:45                    2
      
      Total number of neighbors 1

   3. Run the get router info routing-table bgp command on Spoke1. The system should return the following:

      Routing table for VRF=0
      B       172.16.101.0/24 [200/0] via 10.10.10.254, spoke1, 00:23:57
      B       192.168.4.0/24 [200/0] via 10.10.10.254, spoke1, 00:22:03

   4. Generate traffic between the spokes and check the shortcut tunnel and routing table. Run the diagnose vpn tunnel list command on Spoke1. The system should return the following:

      list all ipsec tunnel in vd 0
      ----
      name=spoke1 ver=1 serial=2 15.1.1.2:0->22.1.1.1:0 tun_id=22.1.1.1
      bound_if=7 lgwy=static/1 tun=intf/0 mode=auto/1 encap=none/536 options[0218]=npu create_dev frag-rfc  accept_traffic=1
      
      proxyid_num=1 child_num=1 refcnt=19 ilast=2 olast=2 ad=r/2
      stat: rxp=1 txp=268 rxb=16428 txb=31243
      dpd: mode=on-idle on=1 idle=5000ms retry=3 count=0 seqno=714
      natt: mode=none draft=0 interval=0 remote_port=0
      proxyid=spoke1 proto=0 sa=1 ref=6 serial=1 auto-negotiate adr
        src: 0:0.0.0.0/0.0.0.0:0
        dst: 0:0.0.0.0/0.0.0.0:0
        SA:  ref=6 options=1a227 type=00 soft=0 mtu=1438 expire=345/0B replaywin=1024
             seqno=10d esn=0 replaywin_lastseq=00000002 itn=0
        life: type=01 bytes=0/0 timeout=2369/2400
        dec: spi=c53a8f5b esp=aes key=16 cbe88682ad896a69290027b6dd8f7162
             ah=sha1 key=20 7bb704b388f83783ac76c2ab0b6c9f7dcf78e93b
        enc: spi=6e3633fc esp=aes key=16 1a0da3f4deed3d16becc9dda57537355
             ah=sha1 key=20 368544044bd9b82592d72476ff93d5055056da8d
        dec:pkts/bytes=1/16364, enc:pkts/bytes=268/48320
        npu_flag=03 npu_rgwy=22.1.1.1 npu_lgwy=15.1.1.2 npu_selid=1 dec_npuid=1 enc_npuid=1
      ----
      name=spoke1_backup ver=1 serial=1 12.1.1.2:0->22.1.1.1:0 tun_id=22.1.1.1
      bound_if=6 lgwy=static/1 tun=intf/0 mode=auto/1 encap=none/536 options[0218]=npu create_dev frag-rfc  accept_traffic=0
      
      proxyid_num=1 child_num=0 refcnt=11 ilast=8 olast=8 ad=/0
      stat: rxp=0 txp=0 rxb=0 txb=0
      dpd: mode=on-idle on=0 idle=5000ms retry=3 count=0 seqno=0
      natt: mode=none draft=0 interval=0 remote_port=0
      proxyid=spoke1_backup proto=0 sa=0 ref=2 serial=1 auto-negotiate adr
        src: 0:0.0.0.0/0.0.0.0:0
        dst: 0:0.0.0.0/0.0.0.0:0
      ----
      name=spoke1_0 ver=1 serial=9 15.1.1.2:4500->13.1.1.2:4500 tun_id=13.1.1.2
      bound_if=7 lgwy=static/1 tun=intf/0 mode=dial_inst/3 encap=none/728 options[02d8]=npu create_dev no-sysctl rgwy-chg frag-rfc  accept_traffic=1
      
       parent=spoke1 index=0
      proxyid_num=1 child_num=0 refcnt=17 ilast=4 olast=4 ad=r/2
      stat: rxp=1 txp=100 rxb=112 txb=4686
      dpd: mode=on-idle on=1 idle=5000ms retry=3 count=0 seqno=231
      natt: mode=keepalive draft=32 interval=10 remote_port=4500
      proxyid=spoke1 proto=0 sa=1 ref=5 serial=1 auto-negotiate adr
        src: 0:0.0.0.0/0.0.0.0:0
        dst: 0:0.0.0.0/0.0.0.0:0
        SA:  ref=6 options=1a227 type=00 soft=0 mtu=1422 expire=447/0B replaywin=1024
             seqno=65 esn=0 replaywin_lastseq=00000002 itn=0
        life: type=01 bytes=0/0 timeout=2368/2400
        dec: spi=c53a8f5c esp=aes key=16 73fd9869547475db78851e6c057ad9b7
             ah=sha1 key=20 6ad3a5b1028f6b33c82ba494a370f13c7f462635
        enc: spi=79cb0f2b esp=aes key=16 52ab0acdc830d58c00e5956a6484654a
             ah=sha1 key=20 baa82aba4106dc60618f6fe95570728656799239
        dec:pkts/bytes=1/46, enc:pkts/bytes=100/11568
        npu_flag=03 npu_rgwy=13.1.1.2 npu_lgwy=15.1.1.2 npu_selid=5 dec_npuid=1 enc_npuid=1

   5. Run the get router info routing-tale bgp command. The system should return the following:

      Routing table for VRF=0
      B       172.16.101.0/24 [200/0] via 10.10.10.254, spoke1, 00:23:57
      B       192.168.4.0/24 [200/0] via 10.10.10.3, spoke1_0 , 00:22:03