FortiGate 400F and 401F fast path architecture
The FortiGate 400F and 401F models feature the following front panel interfaces:
- Two 10/100/1000BASE-T RJ45 (HA and MGMT, not connected to the NP7 processor)
- Sixteen 10/100/1000BASE-T RJ45 (1 to 16)
- Eight 1 GigE SFP (17 to 24)
- Four 10/1 GigE SFP+/SFP (X1 to X4) (X1 and X2 are FortiLink interfaces)
- Four 10 GigE SFP+ (X5 to X8) ultra low latency (ULL)
- Eight 1 GigE SFP (17 to 24)
The FortiGate 400F and 401F each include one NP7 processor. Front panel data interfaces 1 to 24 and X1 to X4 and one of the NP7 processor interfaces connect to the integrated switch fabric (ISF). All data traffic passes from these data interfaces through the ISF to the NP7 processor. All supported traffic passing between any two of these data interfaces can be offloaded by the NP7 processor. Data traffic processed by the CPU takes a dedicated data path through the ISF and the NP7 processor to the CPU.
Front panel data interfaces X5 to X8 are connected directly to the other NP7 processor interface instead of the ISF. Since the ISF introduces latency, interfaces X5 to X8 are ultra low latency (ULL) interfaces, and NP7 traffic entering and exiting the FortiGate through these interfaces experiences lower latency than if it were passing through interfaces that are connected to the ISF. To achieve low latency, traffic must enter and exit the FortiGate through the X5 to X8 interfaces. If traffic enters or exits through other data interfaces it is subject to the latency resulting from passing through the ISF. You can't change the speed of the FortiGate-400F and 401F ULL interfaces .
|
The FortiGate-400F and 401F do not support configuring NPU port mapping, because only one of the NP7 interfaces is connected to the ISF. |
The MGMT interface is not connected to the NP7 processor. Management traffic passes to the CPU over a dedicated management path that is separate from the data path. You can also dedicate separate CPU resources for management traffic to further isolate management processing from data processing (see Dedicated management CPU).
The HA interface is also not connected to the NP7 processor. To help provide better HA stability and resiliency, HA traffic uses a dedicated physical control path that provides HA control traffic separation from data traffic processing.
The separation of management and HA traffic from data traffic keeps management and HA traffic from affecting the stability and performance of data traffic processing.
You can use the following command to display the FortiGate 400F or 401F NP7 configuration. The command output shows a single NP7 named NP#0 is connected to all data interfaces. This interface to NP7 mapping is also shown in the diagram above.
diagnose npu np7 port-list Front Panel Port: Name Max_speed(Mbps) Dflt_speed(Mbps) NP_group Switch_id SW_port_id SW_port_name -------- --------------- --------------- --------------- --------- ---------- ------------ port1 1000 1000 n/a 0 25 port2 1000 1000 n/a 0 24 port3 1000 1000 n/a 0 27 port4 1000 1000 n/a 0 26 port5 1000 1000 n/a 0 29 port6 1000 1000 n/a 0 28 port7 1000 1000 n/a 0 31 port8 1000 1000 n/a 0 30 port9 1000 1000 n/a 0 17 port10 1000 1000 n/a 0 16 port11 1000 1000 n/a 0 19 port12 1000 1000 n/a 0 18 port13 1000 1000 n/a 0 21 port14 1000 1000 n/a 0 20 port15 1000 1000 n/a 0 23 port16 1000 1000 n/a 0 22 port17 1000 1000 n/a 0 7 port18 1000 1000 n/a 0 12 port19 1000 1000 n/a 0 6 port20 1000 1000 n/a 0 13 port21 1000 1000 n/a 0 5 port22 1000 1000 n/a 0 14 port23 1000 1000 n/a 0 4 port24 1000 1000 n/a 0 15 x1 10000 10000 n/a 0 10 x2 10000 10000 n/a 0 9 x3 10000 10000 n/a 0 11 x4 10000 10000 n/a 0 8 x5 10000 10000 n/a n/a n/a n/a x6 10000 10000 n/a n/a n/a n/a x7 10000 10000 n/a n/a n/a n/a x8 10000 10000 n/a n/a n/a n/a -------- --------------- --------------- --------------- --------- ---------- ------------ NP Port: Name Switch_id SW_port_id SW_port_name ------ --------- ---------- ------------ np0_0 0 0 ------ --------- ---------- ------------ * Max_speed: Maximum speed, Dflt_speed: Default speed * SW_port_id: Switch port ID, SW_port_name: Switch port name
The command output also shows the maximum speeds of each interface. Also, that command output shows that the x5 to x8 interfaces are not connected to the internal switch fabric.
The NP7 processor has a bandwidth capacity of 200 Gigabits. You can see from the command output that if all interfaces were operating at their maximum bandwidth the NP7 processor would not be able to offload all the traffic.