Command Line Interface (CLI) Reference

The following commands are supported for FortiAIOps.

Configuration Commands
Show Commands
Diagnostic Commands
Management Commands
System Information

Configuration Commands

The following commands are available to configure FortiAIOps.

Command	Parameters	Description
`config system interface`	`edit <interface port>`	Edit the interface port and enter the port setting mode in the CLI.
	`?`	Displays the various parameters available for this command.
	`abort`	Aborts the port setting mode and exits.
	`next`	Returns to the interface configuration mode.
	`set mode <static\|DHCP>`	Configure the port IP address mode; static or DHCP.
	`set ip <IP/netmask>`	Configure the port IP address (static).
	`set allowaccess <ssh\|https\|http\|ping>`	Configure the admin access type; SSH, THHP, HTTPS, Ping, or SNMP.
	`get`	Obtain the system information.
	`show`	Displays the current interface configuration details.
	`end`	Exit the port configuration mode; the configuration changes then take effect.
`config system`	`admin`	Configures admin users. `edit admin` - Edit admin user details. `set password` - Set the admin user password.
	`dns`	Configures DNS and enters the DNS configuration mode. `set primary` - Configures the primary DNS server.
	`global`	Configures global settings and enters the global configuration mode.
	`interface`	Configures the system interface.
	`ntp`	Configures system NTP information. `set ntpsync` - Enable/disable the system time by synchronizing with the NTP server. `set ntpserver` - Configure the IP address or hostname of the NTP servers (up to 10).

Show Commands

The following commands can be used for viewing configuration information.

Command	Parameters	Description
`show`		Displays bootstrap configuration.
`show full-configuration`		Displays all configuration (includes defaults).

Diagnostic Commands

The following commands are used to diagnose and troubleshoot issues.

Command	Parameters	Description
`diagnose`	`?`	Displays the various parameters available for this command.
	`hardware ?`	Displays the various parameters available for this command.
	`hardware deviceinfo disk`	Displays information of all disks.
	`hardware deviceinfo nic`	Display the available list of NICs.
	`hardware deviceinfo <nic name>`	Displays information of a specific NIC.
	`hardware lspci`	Displays the PCI parameters.
	`hardware lspci tree`	Displays PCI bus tree.
	`hardware lspci verbose`	Displays detailed information about all devices.
	`hardware sysinfo ?`	Displays the various parameters available for this command.
	`hardware sysinfo cpu`	Displays detailed information for all installed CPU(s).
	`hardware sysinfo interrupts`	Displays details of system interruptions.
	`hardware sysinfo iomem`	Displays the memory map of I/O ports.
	`hardware sysinfo ioports`	Display the address list of I/O ports.
	`hardware sysinfo memory`	Displays the system memory details.
	`hardware sysinfo mtrr`	Displays the memory type range register.
	`hardware sysinfo slab`	Displays the memory allocation information.
`diagnose system`	`top all`	Displays the top threads information.
	`top cpu`	Displays processes with the highest CPU usage at the top of the list.
	`load`	Displays system uptime and load information.
	`process <cpu \| mem> <num>`	Displays the processes sorted by specified criteria (default 10 processes).

Management Commands

The following enable some management and other operations in FortiAIOps.

Command	Parameters	Description
`execute`	`?`	Displays the various parameters available for this command.
	`date <YYYY-MM-DD>`	Set the date in the YYYY-MM-DD format.
	`time <HH:MM:SS>`	Set the time in the HH:MM:SS format.
	`factoryreset`	Reset to the factory default settings. Restart the device after the second confirmation prompt.
	`formatlogdisk`	Format the log disk.
	`ping <destination>`	Ping the host name or IPv4 address.
	`traceroute <destination>`	Traceroute of the host name or IPV4 address.
	`reboot`	Reboot the system.
	`shutdown`	Shut down the device.
	`backup config ftp <path> <server fqdn\|ipaddr>[:port] [ftp_user] [ftp_passwd]`	Creates a remote backup of the configuration file from an FTP server.
	`backup config tftp <filename> <server fqdn\|ipaddr>`	Creates a remote backup of the configuration file from a TFTP server.
	`restore image ftp <filename string> <ftp server>[:port] [ftp_user] [ftp_passwd]`	Restores the firmware image from an FTP server using specific details.
	`restore image tftp <filename string> <tftp server>`	Restores the firmware image from a TFTP server.

System Information

The following commands information related to the system configurations.

Command	Parameters	Description
`get system`	`?`	Displays the various parameters available for this command.
	`status`	Displays system status, such as, version, serial number, BIOS details, time stamp, hostname, and so on.
	`admin`	Displays the configuration details of the admin users.
	`admin <username>`	Displays the configuration details of a specific admin user.
	`dns`	Displays the DNS configuration.
	`global`	Displays the configuration details of global attributes.
	`interface`	Displays the interface details, status, and IP address.
	`interface <port>`	Displays the port details, status, and IP address.
	`ntp`	Displays the configuration details and status of NTP server.

Command Line Interface (CLI) Reference

The following commands are supported for FortiAIOps.

Configuration Commands
Show Commands
Diagnostic Commands
Management Commands
System Information

Configuration Commands

The following commands are available to configure FortiAIOps.

Command	Parameters	Description
`config system interface`	`edit <interface port>`	Edit the interface port and enter the port setting mode in the CLI.
	`?`	Displays the various parameters available for this command.
	`abort`	Aborts the port setting mode and exits.
	`next`	Returns to the interface configuration mode.
	`set mode <static\|DHCP>`	Configure the port IP address mode; static or DHCP.
	`set ip <IP/netmask>`	Configure the port IP address (static).
	`set allowaccess <ssh\|https\|http\|ping>`	Configure the admin access type; SSH, THHP, HTTPS, Ping, or SNMP.
	`get`	Obtain the system information.
	`show`	Displays the current interface configuration details.
	`end`	Exit the port configuration mode; the configuration changes then take effect.
`config system`	`admin`	Configures admin users. `edit admin` - Edit admin user details. `set password` - Set the admin user password.
	`dns`	Configures DNS and enters the DNS configuration mode. `set primary` - Configures the primary DNS server.
	`global`	Configures global settings and enters the global configuration mode.
	`interface`	Configures the system interface.
	`ntp`	Configures system NTP information. `set ntpsync` - Enable/disable the system time by synchronizing with the NTP server. `set ntpserver` - Configure the IP address or hostname of the NTP servers (up to 10).

Show Commands

The following commands can be used for viewing configuration information.

Command	Parameters	Description
`show`		Displays bootstrap configuration.
`show full-configuration`		Displays all configuration (includes defaults).

Diagnostic Commands

The following commands are used to diagnose and troubleshoot issues.

Command	Parameters	Description
`diagnose`	`?`	Displays the various parameters available for this command.
	`hardware ?`	Displays the various parameters available for this command.
	`hardware deviceinfo disk`	Displays information of all disks.
	`hardware deviceinfo nic`	Display the available list of NICs.
	`hardware deviceinfo <nic name>`	Displays information of a specific NIC.
	`hardware lspci`	Displays the PCI parameters.
	`hardware lspci tree`	Displays PCI bus tree.
	`hardware lspci verbose`	Displays detailed information about all devices.
	`hardware sysinfo ?`	Displays the various parameters available for this command.
	`hardware sysinfo cpu`	Displays detailed information for all installed CPU(s).
	`hardware sysinfo interrupts`	Displays details of system interruptions.
	`hardware sysinfo iomem`	Displays the memory map of I/O ports.
	`hardware sysinfo ioports`	Display the address list of I/O ports.
	`hardware sysinfo memory`	Displays the system memory details.
	`hardware sysinfo mtrr`	Displays the memory type range register.
	`hardware sysinfo slab`	Displays the memory allocation information.
`diagnose system`	`top all`	Displays the top threads information.
	`top cpu`	Displays processes with the highest CPU usage at the top of the list.
	`load`	Displays system uptime and load information.
	`process <cpu \| mem> <num>`	Displays the processes sorted by specified criteria (default 10 processes).

Management Commands

The following enable some management and other operations in FortiAIOps.

Command	Parameters	Description
`execute`	`?`	Displays the various parameters available for this command.
	`date <YYYY-MM-DD>`	Set the date in the YYYY-MM-DD format.
	`time <HH:MM:SS>`	Set the time in the HH:MM:SS format.
	`factoryreset`	Reset to the factory default settings. Restart the device after the second confirmation prompt.
	`formatlogdisk`	Format the log disk.
	`ping <destination>`	Ping the host name or IPv4 address.
	`traceroute <destination>`	Traceroute of the host name or IPV4 address.
	`reboot`	Reboot the system.
	`shutdown`	Shut down the device.
	`backup config ftp <path> <server fqdn\|ipaddr>[:port] [ftp_user] [ftp_passwd]`	Creates a remote backup of the configuration file from an FTP server.
	`backup config tftp <filename> <server fqdn\|ipaddr>`	Creates a remote backup of the configuration file from a TFTP server.
	`restore image ftp <filename string> <ftp server>[:port] [ftp_user] [ftp_passwd]`	Restores the firmware image from an FTP server using specific details.
	`restore image tftp <filename string> <tftp server>`	Restores the firmware image from a TFTP server.

System Information

The following commands information related to the system configurations.

Command	Parameters	Description
`get system`	`?`	Displays the various parameters available for this command.
	`status`	Displays system status, such as, version, serial number, BIOS details, time stamp, hostname, and so on.
	`admin`	Displays the configuration details of the admin users.
	`admin <username>`	Displays the configuration details of a specific admin user.
	`dns`	Displays the DNS configuration.
	`global`	Displays the configuration details of global attributes.
	`interface`	Displays the interface details, status, and IP address.
	`interface <port>`	Displays the port details, status, and IP address.
	`ntp`	Displays the configuration details and status of NTP server.

Secure Networking

Hybrid Mesh Firewall

NOC Management

LAN

WAN

Unified SASE

Single Vendor SASE

Cloud Network Security

Secure Endpoint Connectivity

Web Application / API Protection

Security Operations

Security Operations Automation

Identity

Early Detection & Prevention

Secure Networking

Hybrid Mesh Firewall

NOC Management

LAN

WAN

Communication & Surveillance

Unified SASE

Single Vendor SASE

Secure Endpoint Connectivity

Cloud Network Security

Cloud-Native Security

Web Application / API Protection

Security Operations

Security Operations Automation

Endpoint

Data Protection

Identity

Email

Early Detection & Prevention

Expert Services

Edge Firewall

Orchestration & management

SD Branch

Application Delivery

Single Vendor SASE

Secure Endpoint Connectivity

Secure Private Access

Thin Edge

Identity

Application Gateway

Enterprise Asset Management

Endpoint Agent

Agentless Security Posture

Identity

Wireless

Switching

Identity

Privilege Acccess Management

Next Generation Firewall

Orchestration & management

Expert Services

Web Application / API Protection

All

All

Account Management

SAAS Management

SAAS Application Security

Managed Services

Platform as a service (PAAS)

Other SAAS Services

4D Pillars

Cloud

Popular Solutions

All Products

User Guide

Command Line Interface (CLI) Reference

Command Line Interface (CLI) Reference

Configuration Commands

Show Commands

Diagnostic Commands

Management Commands

System Information

Command Line Interface (CLI) Reference

Command Line Interface (CLI) Reference

Configuration Commands

Show Commands