Execute a CLI script based on CPU and memory thresholds

Automation stitches can be created to run a CLI script and send an email message when CPU or memory usage exceeds specified thresholds.

In this example, two automation stitches are created that run a CLI script to collect debug information, and then email the results of the script to a specified email address when the CPU usage threshold is exceeded, or memory usage causes the FortiGate to enter conserve mode.

The maximum size of the CLI script action output is 16K characters.

To define CPU and memory usage thresholds:

config system global
    set cpu-use-threshold <percent>
    set memory-use-threshold-extreme <percent>
    set memory-use-threshold-green <percent>
    set memory-use-threshold-red <percent>
end

Where:

cpu-use-threshold	Threshold at which CPU usage is reported, in percent of total possible CPU utilization (default = 90).
memory-use-threshold-extreme	Threshold at which memory usage is considered extreme, and new sessions are dropped, in percent of total RAM (default = 95).
memory-use-threshold-green	Threshold at which memory usage forces the FortiGate to exit conserve mode, in percent of total RAM (default = 82).
memory-use-threshold-red	Threshold at which memory usage forces the FortiGate to enter conserve mode, in percent of total RAM (default = 88).

Configuring the automation stitches

High CPU usage stitch

To create an automation stitch for high CPU usage in the GUI:

1. Go to Security Fabric > Automation and click Create New.
2. Enter the stitch name (auto_high_cpu).
3. Configure the trigger:
   1. Click Add Trigger.
   2. Click Create and select High CPU.
   3. Enter the name, auto_high_cpu.
   4. Click OK.
   5. Select the trigger in the list and click Apply.
4. Configure the CLI Script action:
   1. Click Add Action.
   2. Click Create and select CLI Script.
   3. Enter the following:

      Name	high_cpu_debug
      Script	diagnose debug cli 8 diagnose debug console timestamp enable diagnose debug enable diagnose debug crashlog read get system performance status get system session status diagnose sys session full-stat diagnose firewall iprope state diagnose sys flash list diagnose hardware sysinfo memory diagnose hardware sysinfo slab diagnose hardware sysinfo shm diagnose hardware deviceinfo disk get system arp diagnose ip arp list diagnose ip address list get router info routing-table all get router info kernel diagnose ip rtcache list diagnose sys top-summary diagnose sys top 9 99
      Administrator profile	Select a profile

      

   4. Click OK.
   5. Select the action in the list and click Apply.
5. Configure the Email notification action:
   1. Click Add Action.
   2. Click Create and select Email.
   3. Enter the following:

      Name	auto_high_cpu_email
      To	Enter an email address
      Subject	CSF stitch alert: high_cpu
      Body	%%results%%

   4. Click OK.
   5. Select the action in the list and click Apply.
6. Click OK.

To create an automation stitch for high CPU usage in the CLI:

1. Create the automation trigger:

   config system automation-trigger
       edit "auto_high_cpu"
           set event-type high-cpu
       next
   end

2. Create the automation actions:

   config system automation-action
       edit "high_cpu_debug"
           set action-type cli-script
           set script "diagnose debug cli 8
   diagnose debug console timestamp enable
   diagnose debug enable
   diagnose debug crashlog read
   get system performance status
   get system session status
   diagnose sys session full-stat
   diagnose firewall iprope state
   diagnose sys flash list
   diagnose hardware sysinfo memory
   diagnose hardware sysinfo slab
   diagnose hardware sysinfo shm
   diagnose hardware deviceinfo disk
   get system arp
   diagnose ip arp list
   diagnose ip address list
   get router info routing-table all
   get router info kernel
   diagnose ip rtcache list
   diagnose sys top-summary
   diagnose sys top 9 99"
           set output-size 10
           set timeout 0
           set accprofile "super_admin"
       next
       edit "auto_high_cpu_email"
           set action-type email
           set email-to "person@fortinet.com"
           set email-subject "CSF stitch alert: high_cpu"
           set message "%%results%%"
       next
   end

3. Create the automation stitch:

   config system automation-stitch
       edit "auto_high_cpu"
           set trigger "auto_high_cpu"
           config actions
               edit 1
                   set action "high_cpu_debug"
                   set required enable
               next
               edit 2
                   set action "auto_high_cpu_email"
                   set required enable
               next
           end
       next
   end

High memory usage stitch

To create an automation stitch for high memory usage in the GUI:

1. Go to Security Fabric > Automation and click Create New.
2. Enter the stitch name (auto_high_memory).
3. Configure the trigger:
   1. Click Add Trigger.
   2. Click Create and select Conserve Mode.
   3. Enter the name, auto_high_memory.
   4. Click OK.
   5. Select the trigger in the list and click Apply.
4. Configure the CLI Script action:
   1. Click Add Action.
   2. Click Create and select CLI Script.
   3. Enter the following:

      Name	high_memory_debug
      Script	diagnose debug cli 8 diagnose debug console timestamp enable diagnose debug enable diagnose debug crashlog read get system performance status get system session status diagnose sys session full-stat diagnose firewall iprope state diagnose sys flash list diagnose hardware sysinfo memory diagnose hardware sysinfo slab diagnose hardware sysinfo shm diagnose hardware deviceinfo disk get system arp diagnose ip arp list diagnose ip address list get router info routing-table all get router info kernel diagnose ip rtcache list diagnose sys top-summary diagnose sys top 9 99
      Administrator profile	Select a profile

      

   4. Click OK.
   5. Select the action in the list and click Apply.
5. Configure the Email notification action:
   1. Click Add Action.
   2. Click Create and select Email.
   3. Enter the following:

      Name	auto_high_memory_email
      To	Enter an email address
      Subject	CSF stitch alert: high_memory
      Body	%%results%%

   4. Click OK.
   5. Select the action in the list and click Apply.
6. Click OK.

To create an automation stitch for high memory usage in the CLI:

1. Create the automation trigger:

   config system automation-trigger
       edit "auto_high_memory"
           set event-type low-memory
       next
   end

2. Create the automation actions:

   config system automation-action
       edit "high_memory_debug"
           set action-type cli-script
           set script "diagnose debug cli 8
   diagnose debug console timestamp enable
   diagnose debug enable
   diagnose debug crashlog read
   get system performance status
   get system session status
   diagnose sys session full-stat
   diagnose firewall iprope state
   diagnose sys flash list
   diagnose hardware sysinfo memory
   diagnose hardware sysinfo slab
   diagnose hardware sysinfo shm
   diagnose hardware deviceinfo disk
   get system arp
   diagnose ip arp list
   diagnose ip address list
   get router info routing-table all
   get router info kernel
   diagnose ip rtcache list
   diagnose sys top-summary
   diagnose sys top 9 99"
           set output-size 10
           set timeout 0	
           set accprofile "super_admin"	
       next
       edit "auto_high_memory_email"
           set action-type email
           set email-to "person@fortinet.com"
           set email-subject "CSF stitch alert: high_memory"
           set message "%%results%%"
       next
   end

3. Create the automation stitch:

   config system automation-stitch
       edit "auto_high_memory"
           set trigger "auto_high_memory"
           config actions
               edit 1
                   set action "high_memory_debug"
                   set required enable
               next
               edit 2
                   set action "auto_high_memory_email"
                   set required enable
               next
           end
       next
   end

Results

When the FortiGate enters conserve mode due to the memory-use-threshold-red being exceeded, the GUI displays a notice, and the auto_high_memory automation stitch is triggered. This causes the CLI script to run and the script results are emailed to the specified address.

Here is sample text from the email message:

CSF stitch alert: high_memory
noreply@notification.fortinet.net
Thu 11/21/2019 11:06 AM
John Doe
FGT[FGVM16TM19000000] Automation Stitch:auto_high_memory is triggered.
########## script name: autod.47 ##########
========== #1, 2019-11-21 11:07:24 ==========
FGVM16TM19000000 $  diag deb cli 8
Debug messages will be on for 25 minutes.
FGVM16TM19000000 $  diag deb console timestamp enable
FGVM16TM19000000 $  diag deb enable
FGVM16TM19000000 $  diag deb crashlog read
1: 2019-08-08 11:35:25 the killed daemon is /bin/dhcpcd: status=0x0
2: 2019-08-08 17:52:47 the killed daemon is /bin/pyfcgid: status=0x0
3: 2019-08-23 11:32:31 from=license status=INVALID
4: 2019-08-23 11:32:32 from=license status=INVALID
5: 2019-11-21 09:53:31 from=license status=VALID
...