config firewall ippool
Configure IPv4 IP pools.
config firewall ippool
Description: Configure IPv4 IP pools.
edit <name>
set add-nat64-route [disable|enable]
set arp-intf {string}
set arp-reply [disable|enable]
set associated-interface {string}
set block-size {integer}
set cgn-block-size {integer}
set cgn-client-endip {var-string}
set cgn-client-ipv6shift {integer}
set cgn-client-startip {var-string}
set cgn-fixedalloc [disable|enable]
set cgn-overload [disable|enable]
set cgn-port-end {integer}
set cgn-port-start {integer}
set cgn-spa [disable|enable]
set comments {var-string}
set endip {ipv4-address-any}
set endport {integer}
set name {string}
set nat64 [disable|enable]
set num-blocks-per-user {integer}
set pba-timeout {integer}
set permit-any-host [disable|enable]
set port-per-user {integer}
set source-endip {ipv4-address-any}
set source-startip {ipv4-address-any}
set startip {ipv4-address-any}
set startport {integer}
set subnet-broadcast-in-ippool [disable|enable]
set type [overload|one-to-one|...]
set utilization-alarm-clear {integer}
set utilization-alarm-raise {integer}
next
end
config firewall ippool
|
Parameter |
Description |
Type |
Size |
Default |
||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
add-nat64-route |
Enable/disable adding NAT64 route. |
option |
- |
enable |
||||||||||
|
|
|
|||||||||||||
|
arp-intf |
Select an interface from available options that will reply to ARP requests. (If blank, any is selected). |
string |
Not Specified |
|
||||||||||
|
arp-reply |
Enable/disable replying to ARP requests when an IP Pool is added to a policy. |
option |
- |
enable |
||||||||||
|
|
|
|||||||||||||
|
associated-interface |
Associated interface name. |
string |
Not Specified |
|
||||||||||
|
block-size |
Number of addresses in a block. |
integer |
Minimum value: 64 Maximum value: 4096 |
128 |
||||||||||
|
cgn-block-size * |
Number of ports in a block. |
integer |
Minimum value: 64 Maximum value: 4096 |
128 |
||||||||||
|
cgn-client-endip * |
Final client IPv4 address (inclusive) (format xxx.xxx.xxx.xxx, Default: 0.0.0.0). |
var-string |
Not Specified |
|
||||||||||
|
cgn-client-ipv6shift * |
IPv6 shift for fixed-allocation. |
integer |
Minimum value: 0 Maximum value: 127 |
0 |
||||||||||
|
cgn-client-startip * |
First client IPv4 address (inclusive) (format xxx.xxx.xxx.xxx, Default: 0.0.0.0). |
var-string |
Not Specified |
|
||||||||||
|
cgn-fixedalloc * |
Enable/disable fixed-allocation mode. |
option |
- |
disable |
||||||||||
|
|
|
|||||||||||||
|
cgn-overload * |
Enable/disable overload mode. |
option |
- |
disable |
||||||||||
|
|
|
|||||||||||||
|
cgn-port-end * |
Ending public port can be allocated. |
integer |
Minimum value: 1024 Maximum value: 65535 |
65530 |
||||||||||
|
cgn-port-start * |
Starting public port can be allocated. |
integer |
Minimum value: 1024 Maximum value: 65535 |
5117 |
||||||||||
|
cgn-spa * |
Enable/disable single port allocation mode. |
option |
- |
disable |
||||||||||
|
|
|
|||||||||||||
|
comments |
Comment. |
var-string |
Not Specified |
|
||||||||||
|
endip |
Final IPv4 address (inclusive) in the range for the address pool (format xxx.xxx.xxx.xxx, Default: 0.0.0.0). |
ipv4-address-any |
Not Specified |
0.0.0.0 |
||||||||||
|
endport |
Final port number (inclusive) in the range for the address pool (Default: 65533). |
integer |
Minimum value: 5117 Maximum value: 65533 |
65533 |
||||||||||
|
name |
IP pool name. |
string |
Not Specified |
|
||||||||||
|
nat64 |
Enable/disable NAT64. |
option |
- |
disable |
||||||||||
|
|
|
|||||||||||||
|
num-blocks-per-user |
Number of addresses blocks that can be used by a user. |
integer |
Minimum value: 1 Maximum value: 128 |
8 |
||||||||||
|
pba-timeout |
Port block allocation timeout (seconds). |
integer |
Minimum value: 3 Maximum value: 300 |
30 |
||||||||||
|
permit-any-host |
Enable/disable full cone NAT. |
option |
- |
disable |
||||||||||
|
|
|
|||||||||||||
|
port-per-user |
Number of port for each user. |
integer |
Minimum value: 32 Maximum value: 60416 |
0 |
||||||||||
|
source-endip |
Final IPv4 address (inclusive) in the range of the source addresses to be translated (format xxx.xxx.xxx.xxx, Default: 0.0.0.0). |
ipv4-address-any |
Not Specified |
0.0.0.0 |
||||||||||
|
source-startip |
First IPv4 address. |
ipv4-address-any |
Not Specified |
0.0.0.0 |
||||||||||
|
startip |
First IPv4 address (inclusive) in the range for the address pool (format xxx.xxx.xxx.xxx, Default: 0.0.0.0). |
ipv4-address-any |
Not Specified |
0.0.0.0 |
||||||||||
|
startport |
First port number (inclusive) in the range for the address pool (Default: 5117). |
integer |
Minimum value: 5117 Maximum value: 65533 |
5117 |
||||||||||
|
subnet-broadcast-in-ippool |
Enable/disable inclusion of the subnetwork address and broadcast IP address in the NAT64 IP pool. |
option |
- |
enable |
||||||||||
|
|
|
|||||||||||||
|
type |
IP pool type (overload, one-to-one, fixed port range, or port block allocation). |
option |
- |
overload |
||||||||||
|
|
|
|||||||||||||
|
utilization-alarm-clear * |
Pool utilization alarm clear threshold. |
integer |
Minimum value: 40 Maximum value: 100 |
80 |
||||||||||
|
utilization-alarm-raise * |
Pool utilization alarm raise threshold. |
integer |
Minimum value: 50 Maximum value: 100 |
100 |
||||||||||
* This parameter may not exist in some models.