Known issues

Known issues

The following issues have been identified in FortiGate-6000 and FortiGate-7000 FortiOS 6.2.9 Build 1206. For inquires about a particular bug, please contact Customer Service & Support. The Known issues described in the FortiOS 6.2.9 release notes also apply to FortiGate-6000 and 7000 FortiOS 6.2.9 Build 1206.

Bug ID	Description
549983	A FortiGate-6000 or 7000 can't communicate with FortiManager over a FortiGate-6000 or 7000 data interface.
609131	When DHCP leases are cleared from the primary FortiGate in an HA cluster, they are not cleared from the secondary FortiGate.
647254	After an FGCP HA failover, duplicate IPv4 ECMP routes are installed on all FPCs except for the primary FPC of the new primary FortiGate-6000.
697423	FortiGate-7000F cross-FIM LAGs may not work as expected.
700544	FortiAnalyzer may not display FortiGate-7000F resource usage accurately or on time.
701258	Speeds of FortiGate-7121F split interfaces may not be as expected. For example, if you change the speed of the QSFPDD interface to 100Gfull and then split this interface into four interfaces, the speed of each of the resulting interfaces will also be 100Gfull.
704635	Some transceiver types are not displayed correctly on the FortiGate-7000F GUI.
724543	Outbound bandwidth traffic statistics are showing incorrectly on individual FIM and FPM GUI pages.
734898	Under some conditions when a FortiGate-6000 or 7000 is very busy, when making configuration changes either manually or using a script, the `cmdbsvr` application may crash with a signal 11 segmentation fault. This problem can occur on a standalone FortiGate-6000 or 7000 or on FortiGate-6000s or 7000s in an FGCP HA cluster.
735464	The `diagnose ips filter` command is not broadcast from the management board or the primary FIM to all FPCs or FPMs.
763074	Two interfaces may be incorrectly assigned the same SNMP index.
767742	Because of a limitation of the FIM-7921F switch hardware, the FortiGate-7121F with FIM-7921Fs does not support adding VLANs to flow rules. The `vlan` setting of the `config load-balance flow-rule` command is ignored.
778239	For all FortiGate-6000 and 7000 models, the CLI allows you to add up to 512 flow rules. However, the number of flow rules that you can add is actually limited by the FortiGate-6000 and 7000 internal switch hardware: All FortiGate-6000F models support up to 256 flow rules. All FortiGate-7000E models support up to 512 flow-rules. All FortiGate-7000F models support up to 52 flow-rules.

Known issues

Bug ID

Description

549983

A FortiGate-6000 or 7000 can't communicate with FortiManager over a FortiGate-6000 or 7000 data interface.

609131

When DHCP leases are cleared from the primary FortiGate in an HA cluster, they are not cleared from the secondary FortiGate.

647254

After an FGCP HA failover, duplicate IPv4 ECMP routes are installed on all FPCs except for the primary FPC of the new primary FortiGate-6000.

697423

FortiGate-7000F cross-FIM LAGs may not work as expected.

700544

FortiAnalyzer may not display FortiGate-7000F resource usage accurately or on time.

701258

Speeds of FortiGate-7121F split interfaces may not be as expected. For example, if you change the speed of the QSFPDD interface to 100Gfull and then split this interface into four interfaces, the speed of each of the resulting interfaces will also be 100Gfull.

704635

Some transceiver types are not displayed correctly on the FortiGate-7000F GUI.

724543

Outbound bandwidth traffic statistics are showing incorrectly on individual FIM and FPM GUI pages.

734898

Under some conditions when a FortiGate-6000 or 7000 is very busy, when making configuration changes either manually or using a script, the cmdbsvr application may crash with a signal 11 segmentation fault. This problem can occur on a standalone FortiGate-6000 or 7000 or on FortiGate-6000s or 7000s in an FGCP HA cluster.

735464

The diagnose ips filter command is not broadcast from the management board or the primary FIM to all FPCs or FPMs.

763074

Two interfaces may be incorrectly assigned the same SNMP index.

767742

Because of a limitation of the FIM-7921F switch hardware, the FortiGate-7121F with FIM-7921Fs does not support adding VLANs to flow rules. The vlan setting of the config load-balance flow-rule command is ignored.

778239

For all FortiGate-6000 and 7000 models, the CLI allows you to add up to 512 flow rules. However, the number of flow rules that you can add is actually limited by the FortiGate-6000 and 7000 internal switch hardware:

All FortiGate-6000F models support up to 256 flow rules.
All FortiGate-7000E models support up to 512 flow-rules.
All FortiGate-7000F models support up to 52 flow-rules.

FortiGate-7000 Release Notes

Known issues

Known issues