Version:

Version:

Version:

Version:

Version:

Version:


Table of Contents

Administration Guide

Diagnostic monitoring interface module status

With the diagnostic monitoring interface (DMI), you can view the following information

  • Module details (detail)
  • Eeprom contents (eeprom)
  • Module limits (limit)
  • Module status (status)
  • Summary information of all a port’s modules (summary)
Using the GUI:

Go to Switch > Monitor > Modules.

Using the CLI:

Use the following commands to enable or disable DMI status for the port. If you set the status to global, the port setting will match the global setting:

config switch physical-port

edit <interface>

set dmi-status {disable | enable | global}

end

 

Use the get switch modules detail/status command to display DMI information:

S148FNTF20000098 # get switch modules detail port50
____________________________________________________________
Port(port50)
identifier       SFP/SFP+
connector        Unk(0x00) 
transceiver      1000-Base-T 
encoding         8B/10B
Length Decode Common
	length_smf_1km  N/A
	length_cable    100 meter
SFP Specific
	length_smf_100m N/A
	length_50um_om2 N/A
	length_62um_om1 N/A
	length_50um_om3 N/A
vendor           FINISAR CORP.
vendor_oid       0x009065
vendor_pn        FCLF-8521-3
vendor_rev       
vendor_sn        PU71L2H
manuf_date       08/15/2015 

The following is an example of the output for the get switch modules status command:

FS1E48T419000004 # get switch modules status port50
____________________________________________________________
Port(port50)
temperature      23.957031 C
voltage          3.293100 volts
alarm_flags[0]   0x0000
warning_flags[0] 0x0000
laser_bias[0]    0.761600 mAmps
tx_power[0]      -2.246809 dBm
rx_power[0]      -2.926854 dBm
alarm_flags[1]   0x0000
warning_flags[1] 0x0000
laser_bias[1]    0.755200 mAmps
tx_power[1]      -1.993517 dBm
rx_power[1]      -3.300326 dBm
alarm_flags[2]   0x0000
warning_flags[2] 0x0000
laser_bias[2]    0.761600 mAmps
tx_power[2]      -2.105603 dBm
rx_power[2]      -2.486439 dBm
alarm_flags[3]   0x0000
warning_flags[3] 0x0000
laser_bias[3]    0.748800 mAmps
tx_power[3]      -2.128939 dBm
rx_power[3]      -2.641617 dBm
options          0x000F ( TX_DISABLE TX_FAULT RX_LOSS TX_POWER_LEVEL1 )
options_status   0x0008 ( TX_POWER_LEVEL1 )

Diagnostic monitoring interface module status

With the diagnostic monitoring interface (DMI), you can view the following information

  • Module details (detail)
  • Eeprom contents (eeprom)
  • Module limits (limit)
  • Module status (status)
  • Summary information of all a port’s modules (summary)
Using the GUI:

Go to Switch > Monitor > Modules.

Using the CLI:

Use the following commands to enable or disable DMI status for the port. If you set the status to global, the port setting will match the global setting:

config switch physical-port

edit <interface>

set dmi-status {disable | enable | global}

end

 

Use the get switch modules detail/status command to display DMI information:

S148FNTF20000098 # get switch modules detail port50
____________________________________________________________
Port(port50)
identifier       SFP/SFP+
connector        Unk(0x00) 
transceiver      1000-Base-T 
encoding         8B/10B
Length Decode Common
	length_smf_1km  N/A
	length_cable    100 meter
SFP Specific
	length_smf_100m N/A
	length_50um_om2 N/A
	length_62um_om1 N/A
	length_50um_om3 N/A
vendor           FINISAR CORP.
vendor_oid       0x009065
vendor_pn        FCLF-8521-3
vendor_rev       
vendor_sn        PU71L2H
manuf_date       08/15/2015 

The following is an example of the output for the get switch modules status command:

FS1E48T419000004 # get switch modules status port50
____________________________________________________________
Port(port50)
temperature      23.957031 C
voltage          3.293100 volts
alarm_flags[0]   0x0000
warning_flags[0] 0x0000
laser_bias[0]    0.761600 mAmps
tx_power[0]      -2.246809 dBm
rx_power[0]      -2.926854 dBm
alarm_flags[1]   0x0000
warning_flags[1] 0x0000
laser_bias[1]    0.755200 mAmps
tx_power[1]      -1.993517 dBm
rx_power[1]      -3.300326 dBm
alarm_flags[2]   0x0000
warning_flags[2] 0x0000
laser_bias[2]    0.761600 mAmps
tx_power[2]      -2.105603 dBm
rx_power[2]      -2.486439 dBm
alarm_flags[3]   0x0000
warning_flags[3] 0x0000
laser_bias[3]    0.748800 mAmps
tx_power[3]      -2.128939 dBm
rx_power[3]      -2.641617 dBm
options          0x000F ( TX_DISABLE TX_FAULT RX_LOSS TX_POWER_LEVEL1 )
options_status   0x0008 ( TX_POWER_LEVEL1 )