Fortinet white logo
Fortinet docs logo DOCUMENT LIBRARY
Fortinet white logo
Fortinet docs logo DOCUMENT LIBRARY
Products Best Practices Hardware Guides Products A-Z
Summary
By Solution
By 4D Pillars
By Cloud
Secure Networking
Unified SASE
Security Operations
Secure SD-WAN
Secure Access Service Edge (SASE)
ZTNA
LAN Edge
Identity and Access Management
Next Generation Firewall
Public Cloud
Private Cloud
FortiCloud
Secure Networking
  • Hybrid Mesh Firewall
  • NOC Management
  • LAN
  • WAN
    • More >>
    Unified SASE
  • Single Vendor SASE
  • Cloud Network Security
  • Secure Endpoint Connectivity
  • Web Application / API Protection
    • More >>
    Security Operations
  • Security Operations Automation
  • Identity
  • Early Detection & Prevention
    • More >>
    Secure Networking
  • Hybrid Mesh Firewall
  • NOC Management
  • LAN
  • WAN
  • Communication & Surveillance
    • Unified SASE
  • Single Vendor SASE
  • Secure Endpoint Connectivity
  • Cloud Network Security
  • Cloud-Native Security
  • Web Application / API Protection
    • Security Operations
  • Security Operations Automation
  • Endpoint
  • Data Protection
  • Identity
  • Email
  • Early Detection & Prevention
  • Expert Services
  • Edge Firewall
  • Orchestration & management
  • SD Branch
  • Application Delivery
  • Single Vendor SASE
  • Secure Endpoint Connectivity
  • Secure Private Access
  • Thin Edge
  • Identity
  • Application Gateway
  • Enterprise Asset Management
  • Endpoint Agent
  • Agentless Security Posture
  • Identity
  • Wireless
  • Switching
  • Identity
  • Privilege Acccess Management
  • Next Generation Firewall
  • Orchestration & management
  • Expert Services
  • All
  • All
  • Account Management
  • SAAS Management
  • SAAS Application Security
  • Managed Services
  • Platform as a service (PAAS)
  • Other SAAS Services
    • 4D Resources
    Solution Hubs
  • 4D Pillars
  • Cloud
  • Popular Solutions

    • Release Notes

    Home FortiSwitch 7.0.3 Release Notes
    7.0.3
    7.2.9
    7.2.8
    7.2.7
    7.2.6
    7.2.5
    7.2.4
    7.2.3
    7.2.2
    7.2.1
    7.2.0
    7.0.11
    7.0.10
    7.0.9
    7.0.8
    7.0.7
    7.0.6
    7.0.5
    7.0.4
    7.0.3
    7.0.2
    7.0.1
    7.0.0
    6.4.15
    6.4.14
    6.4.13
    6.4.12
    6.4.11
    6.4.10
    6.4.9
    6.4.8
    6.4.7
    6.4.6
    6.4.5
    6.4.4
    6.4.3
    6.4.2
    6.4.1
    6.4.0
    6.2.8
    6.2.7
    6.2.6
    6.2.5
    6.2.4
    6.2.3
    6.2.2
    6.2.1
    6.2.0
    6.0.7
    6.0.6
    6.0.5
    6.0.4
    6.0.3
    6.0.2
    6.0.1
    6.0.0
    3.6.12
    3.6.11
    3.6.10
    3.6.9
    3.6.8
    3.6.7
    3.6.6
    3.6.5
    3.6.4
    3.6.3
    3.6.2
    3.6.1
    3.6.0
    3.5.6
    3.5.5
    3.5.4
    3.5.3
    3.5.2
    3.5.1
    3.5.0
    3.4.3
    3.4.2
    3.4.1
    3.4.0
    3.3.3
    3.3.2
    3.3.1

    Known issues

    Known issues

    The following known issues have been identified with FortiSwitchOS 7.0.3. For inquiries about a particular bug or to report a bug, please contact Fortinet Customer Service & Support.

    Bug ID Description
    382518, 417024, 417073, 417099, 438441 DHCP snooping and dynamic ARP inspection (DAI) do not work with private VLANs (PVLANs).
    414972 IGMP snooping might not work correctly when used with 802.1x Dynamic VLAN functionality.
    480605 When DHCP snooping is enabled on the FSR-112D-POE, the switched virtual interface (SVI) cannot get the IP address from the DHCP server.

    Workarounds:
    —Use a static IP address in the SVI when DHCP snooping is enabled on that VLAN.
    —Temporarily disable dhcp-snooping on vlan, issue the execute interface dhcpclient-renew <interface> command to renew the IP address. After the SVI gets the IP address from the DHCP server, you can enable DHCP snooping.
    510943 The time-domain reflectometer (TDR) function (cable diagnostics feature) reports unexpected values.

    Workaround: When using the cable diagnostics feature on a port (with the diagnose switch physical-ports cable-diag <physical port name> CLI command), ensure that the physical link on its neighbor port is down. You can disable the neighbor ports or physically remove the cables.
    542031 For the 5xx switches, the diagnose switch physical-ports led-flash command flashes only the SFP port LEDs, instead of all the port LEDs.
    548783 Some models support setting the mirror destination to “internal.” This is intended only for debugging purposes and might prevent critical protocols from operating on ports being used as mirror sources.
    572052 Backup files from FortiSwitchOS 3.x that have 16-character-long passwords fail when restored on FortiSwitchOS 6.x. In FortiSwitchOS 6.x, file backups fail with passwords longer than 15 characters.

    Workaround: Use passwords with a maximum of 15 characters for FortiSwitchOS 3.x and 6.x.
    585550 When packet sampling is enabled on an interface, packets that should be dropped by uRPF will be forwarded.
    606044/610149 The results are inaccurate when running cable diagnostics on the FS-108E, FS-124E, FS-108E-POE, FS-108E-FPOE, FS-124E-POE, FS-124E-FPOE, FS-148E, and FS-148E-POE models.
    609375 The FortiSwitchOS supports four priority levels (critical, high, medium, and low); however, The SNMP Power Ethernet MIB only supports three levels. To support the MIB, a power priority of medium is returned as low for the PoE MIB.

    724813

    The set enforce-first-as {disable | enable} command should have been placed under config neighbor and does not work in its current location (directly under config router bgp). There is no patch available for this issue.
    734917 When you configure a PIM multicast flow with a range of group addresses for SVIs and the group address range overlaps with a dynamic IGMPv3 group receiver that has joined groups in a different VLAN, then the dynamic IGMPv3 receiver will still receive multicast traffic unexpectedly even after leaving the joined groups.

    776675

    • FortiSwitchOS cannot use the NAS-Filter-Rule when it exceeds 65 characters.

    • If you specify more than one port or port range (for example, 10.105.0.106/24 100,200,300 or 10.105.0.106/24 100-200,300, 700-900) when defining the source or destination in a dynamic ACL entry, FortiSwitchOS applies the first port or port range and ignores the rest.

    • If you specify the destination port after the any keyword, you must specify any 0.0.0.0/0 <port_number>. For example, instead of permit in TCP any to any 90 cnt, use permit in TCP any to any 0.0.0.0/0 90 cnt instead.

    784585

    When a dynamic LACP trunk has formed between switches in an MRP ring, the MRP ring cannot be closed. Deleting the dynamic LACP trunk does not fix this issue. MRP supports only physical ports and static trunks; MRP does not support dynamic LACP trunks.

    Workaround: Disable MRP and then re-enable MRP.
    Previous
    Next

    Known issues

    Known issues

    The following known issues have been identified with FortiSwitchOS 7.0.3. For inquiries about a particular bug or to report a bug, please contact Fortinet Customer Service & Support.

    Bug ID Description
    382518, 417024, 417073, 417099, 438441 DHCP snooping and dynamic ARP inspection (DAI) do not work with private VLANs (PVLANs).
    414972 IGMP snooping might not work correctly when used with 802.1x Dynamic VLAN functionality.
    480605 When DHCP snooping is enabled on the FSR-112D-POE, the switched virtual interface (SVI) cannot get the IP address from the DHCP server.

    Workarounds:
    —Use a static IP address in the SVI when DHCP snooping is enabled on that VLAN.
    —Temporarily disable dhcp-snooping on vlan, issue the execute interface dhcpclient-renew <interface> command to renew the IP address. After the SVI gets the IP address from the DHCP server, you can enable DHCP snooping.
    510943 The time-domain reflectometer (TDR) function (cable diagnostics feature) reports unexpected values.

    Workaround: When using the cable diagnostics feature on a port (with the diagnose switch physical-ports cable-diag <physical port name> CLI command), ensure that the physical link on its neighbor port is down. You can disable the neighbor ports or physically remove the cables.
    542031 For the 5xx switches, the diagnose switch physical-ports led-flash command flashes only the SFP port LEDs, instead of all the port LEDs.
    548783 Some models support setting the mirror destination to “internal.” This is intended only for debugging purposes and might prevent critical protocols from operating on ports being used as mirror sources.
    572052 Backup files from FortiSwitchOS 3.x that have 16-character-long passwords fail when restored on FortiSwitchOS 6.x. In FortiSwitchOS 6.x, file backups fail with passwords longer than 15 characters.

    Workaround: Use passwords with a maximum of 15 characters for FortiSwitchOS 3.x and 6.x.
    585550 When packet sampling is enabled on an interface, packets that should be dropped by uRPF will be forwarded.
    606044/610149 The results are inaccurate when running cable diagnostics on the FS-108E, FS-124E, FS-108E-POE, FS-108E-FPOE, FS-124E-POE, FS-124E-FPOE, FS-148E, and FS-148E-POE models.
    609375 The FortiSwitchOS supports four priority levels (critical, high, medium, and low); however, The SNMP Power Ethernet MIB only supports three levels. To support the MIB, a power priority of medium is returned as low for the PoE MIB.

    724813

    The set enforce-first-as {disable | enable} command should have been placed under config neighbor and does not work in its current location (directly under config router bgp). There is no patch available for this issue.
    734917 When you configure a PIM multicast flow with a range of group addresses for SVIs and the group address range overlaps with a dynamic IGMPv3 group receiver that has joined groups in a different VLAN, then the dynamic IGMPv3 receiver will still receive multicast traffic unexpectedly even after leaving the joined groups.

    776675

    • FortiSwitchOS cannot use the NAS-Filter-Rule when it exceeds 65 characters.

    • If you specify more than one port or port range (for example, 10.105.0.106/24 100,200,300 or 10.105.0.106/24 100-200,300, 700-900) when defining the source or destination in a dynamic ACL entry, FortiSwitchOS applies the first port or port range and ignores the rest.

    • If you specify the destination port after the any keyword, you must specify any 0.0.0.0/0 <port_number>. For example, instead of permit in TCP any to any 90 cnt, use permit in TCP any to any 0.0.0.0/0 90 cnt instead.

    784585

    When a dynamic LACP trunk has formed between switches in an MRP ring, the MRP ring cannot be closed. Deleting the dynamic LACP trunk does not fix this issue. MRP supports only physical ports and static trunks; MRP does not support dynamic LACP trunks.

    Workaround: Disable MRP and then re-enable MRP.
    Previous
    Next