Fortinet black logo

Administration Guide

Diagnostic monitoring interface module status

Copy Link
Copy Doc ID 962fb21b-9bd3-11eb-b70b-00505692583a:861227
Download PDF

Diagnostic monitoring interface module status

With diagnostic monitoring interface (DMI), you can view the following information

  • Module details (detail)
  • Eeprom contents (eeprom)
  • Module limits (limit)
  • Module status (status)
  • Summary information of all a port’s modules (summary)
Using the GUI:

Go to Switch > Monitor > Modules.

Using the CLI:

Use the following commands to enable or disable DMI status for the port. If you set the status to global, the port setting will match the global setting:

config switch physical-port

edit <interface>

set dmi-status {disable | enable | global}

end

Use the get switch modules detail/status command to display DMI information:

FS108E3W14000720 # get switch modules detail port10

____________________________________________________________

Port(port10)

identifier SFP/SFP+

connector Unk (0x00)

transceiver 1000-Base-T

encoding 8B/10B

Length Decode Common

length_smf_1km N/A

length_cable 100 meter

SFP Specific

length_smf_100m N/A

length_50um_om2 N/A

length_62um_om1 N/A

length_50um_om3 N/A

vendor FINISAR CORP.

vendor_oid 0x009065

vendor_pn FCLF-8521-3

vendor_rev A

vendor_sn PBR1X35

manuf_date 06/20/2007

The following is an example of the output for the switch modules status command:

FS108E3W14000720 # get switch modules status port9

____________________________________________________________

Port(port9)

alarm_flags 0x0040

warning_flags 0x0040

temperature 18.792969 C

voltage 3.315100 volts

laser_bias 0.750800 mAmps

tx_power -2.502637 dBm

rx_power -40.000000 dBm

options 0x000F ( TX_DISABLE TX_FAULT RX_LOSS TX_POWER_LEVEL1 )

options_status 0x000C ( RX_LOSS TX_POWER_LEVEL1 )

Diagnostic monitoring interface module status

With diagnostic monitoring interface (DMI), you can view the following information

  • Module details (detail)
  • Eeprom contents (eeprom)
  • Module limits (limit)
  • Module status (status)
  • Summary information of all a port’s modules (summary)
Using the GUI:

Go to Switch > Monitor > Modules.

Using the CLI:

Use the following commands to enable or disable DMI status for the port. If you set the status to global, the port setting will match the global setting:

config switch physical-port

edit <interface>

set dmi-status {disable | enable | global}

end

Use the get switch modules detail/status command to display DMI information:

FS108E3W14000720 # get switch modules detail port10

____________________________________________________________

Port(port10)

identifier SFP/SFP+

connector Unk (0x00)

transceiver 1000-Base-T

encoding 8B/10B

Length Decode Common

length_smf_1km N/A

length_cable 100 meter

SFP Specific

length_smf_100m N/A

length_50um_om2 N/A

length_62um_om1 N/A

length_50um_om3 N/A

vendor FINISAR CORP.

vendor_oid 0x009065

vendor_pn FCLF-8521-3

vendor_rev A

vendor_sn PBR1X35

manuf_date 06/20/2007

The following is an example of the output for the switch modules status command:

FS108E3W14000720 # get switch modules status port9

____________________________________________________________

Port(port9)

alarm_flags 0x0040

warning_flags 0x0040

temperature 18.792969 C

voltage 3.315100 volts

laser_bias 0.750800 mAmps

tx_power -2.502637 dBm

rx_power -40.000000 dBm

options 0x000F ( TX_DISABLE TX_FAULT RX_LOSS TX_POWER_LEVEL1 )

options_status 0x000C ( RX_LOSS TX_POWER_LEVEL1 )