Version:

Version:

Version:

Version:

Version:

Version:

Version:

Version:


Table of Contents

External Systems Configuration Guide

APC Netbotz Environmental Monitor

What is Monitored and Collected

Protocol

Information Discovered

Metrics collected

Used for

SNMP (V1, V2c) Host name, Hardware model, Network interfaces

Temperature: Sensor Id, Sensor label, Enclosure Id, Temperature

Relative Humidity: Sensor Id, Sensor label, Enclosure Id, Relative Humidity

Air Flow: Sensor Id, Sensor label, Enclosure Id, Air Flow

Dew Point Temperature: Sensor Id, Sensor label, Enclosure Id, Dew Point Temperature

Current: Sensor Id, Sensor label, Enclosure Id, Current

Audio Sensor Reading: Sensor Id, Sensor label, Enclosure Id, Audio Sensor Reading

Dry Contact Sensor Reading: Sensor Id, Sensor label, Enclosure Id, Dry Contact Sensor Reading

Availability and Performance Monitoring

 

 

Door Switch Sensor Reading: Sensor Id, Sensor label, Enclosure Id, Door Switch Sensor Reading (Open/Close)

Camera Motion Sensor Reading: Sensor Id, Sensor label, Enclosure Id, Camera Motion Sensor Reading (Motion/No Motion)

Hadware Status (for NBRK0200): Contact Status, Output Relay Status, Outlet Status, Alarm Device Status, Memory Sensor Status, Memory Output Status, Memory Outlet Status, memory Beacon Status

EMS Status (for NBRK0200): EMS Hardware Status, Connection State

Hardware Probe (for NBRK0200): Sensor Id, Temperature, Relative Humidity, Connection State Code

Module Sensor (for NBRK0200): Sensor Name, Sensor location, Temperature, Relative Humidity, Connection State Code

 

SNMP Trap (V1, V2c)

SNMP Trap

See Event Types for more information about viewing the SNMP traps collected by FortiSIEM for this device.

Availability and Performance Monitoring

 

Event Types

In ADMIN > Device Support > Event Types, search for "NetBotz" to see the event types associated with this application or device. 

Event types for NetBotz NBRK0200

  • PH_DEV_MON_HW_STATUS

    [PH_DEV_MON_HW_STATUS]:[eventSeverity]=PHL_INFO,[fileName]=deviceNetBotz.cpp,[lineNumber]=1642,[hostName]=Unknown,[hostIpAddr]=10.62.97.61,[hwStatusCode]=2,[hwProbeStatus]=2,[hwInputContactStatus]=2,[hwOutputRelayStatus]=0,[hwOutletStatus]=2,[hwAlarmDeviceStatus]=0,[hwMemSensorStatus]=0,[hwMemOutputStatus]=2,[hwMemOutletStatus]=2,[hwMemBeaconStatus]=2,[phLogDetail]=
  • PH_DEV_MON_HW_EMS_STATUS

    [PH_DEV_MON_HW_EMS_STATUS]:[eventSeverity]=PHL_INFO,[fileName]=deviceNetBotz.cpp,[lineNumber]=1871,[hostName]=Unknown,[hostIpAddr]=10.62.97.61,[reptDevName]=Unknown,[emsHwStatus]=0,[phyMachConnectionStateCode]=2,[hwLogStatus]=1,[phLogDetail]=
  • PH_DEV_MON_HW_PROBE

    [PH_DEV_MON_HW_PROBE]:[eventSeverity]=PHL_INFO,[fileName]=deviceNetBotz.cpp,[lineNumber]=2100,[hostName]=Unknown,[hostIpAddr]=10.62.97.61,[envSensorLabel]=Sensor MM:4,[envTempDegF]=74,[envTempHighThreshDegF]=138,[envHumidityRel]=51,[envHumidityRelHighThresh]=90,[envHumidityRelLowThresh]=10,[serialNumber]=L3,[phyMachConnectionStateCode]=3,[maxTempThresh]=140,[minTempThresh]=32,[maxHumidityThresh]=99,[minHumidityThresh]=0,[phLogDetail]=
  • PH_DEV_MON_HW_MODULE_SENSOR

    [PH_DEV_MON_HW_MODULE_SENSOR]:[eventSeverity]=PHL_INFO,[fileName]=deviceNetBotz.cpp,[lineNumber]=2567,[hostName]=Unknown,[hostIpAddr]=10.62.97.61,[moduleNumber]=0,[envSensorId]=1,[envSensorLabel]=Sensor MM:1,[envSensorLoc]=Orland Park Server,[envTempDegF]=74,[envHumidityRel]=50,[phyMachConnectionStateCode]=1,[hwAlarmDevicetatus]=1,[phLogDetail]=

Rules

In RESOURCES > Rules, search for "NetBotz" in the main content panel Search... field to see the rules associated with this application or device. 

Reports

In RESOURCES > Reports, search for "NetBotz" in the main content panel Search... field to see the reports associated with this application or device. 

Configuration

SNMP

FortiSIEM uses SNMP to discover and monitor this device. Make sure SNMP is enabled for the device as directed in its product documentation. For more information, refer to sections "Discovery Settings" and "Setting Credentials" in the User Guide

SNMP Trap

FortiSIEM processes events from this device via SNMP traps sent by the device. Configure the device to send SNMP traps to FortiSIEM as directed in the device's product documentation, and FortiSIEM will parse the contents.

Setting Access Credentials

Set these Access Method Definition values to allow FortiSIEM to communicate with your device.

Setting Value
Name <set name>
Device Type APC NetBotz
Access Protocol See Access Credentials
Port See Access Credentials
Password config See Password Configuration

APC Netbotz Environmental Monitor

What is Monitored and Collected

Protocol

Information Discovered

Metrics collected

Used for

SNMP (V1, V2c) Host name, Hardware model, Network interfaces

Temperature: Sensor Id, Sensor label, Enclosure Id, Temperature

Relative Humidity: Sensor Id, Sensor label, Enclosure Id, Relative Humidity

Air Flow: Sensor Id, Sensor label, Enclosure Id, Air Flow

Dew Point Temperature: Sensor Id, Sensor label, Enclosure Id, Dew Point Temperature

Current: Sensor Id, Sensor label, Enclosure Id, Current

Audio Sensor Reading: Sensor Id, Sensor label, Enclosure Id, Audio Sensor Reading

Dry Contact Sensor Reading: Sensor Id, Sensor label, Enclosure Id, Dry Contact Sensor Reading

Availability and Performance Monitoring

 

 

Door Switch Sensor Reading: Sensor Id, Sensor label, Enclosure Id, Door Switch Sensor Reading (Open/Close)

Camera Motion Sensor Reading: Sensor Id, Sensor label, Enclosure Id, Camera Motion Sensor Reading (Motion/No Motion)

Hadware Status (for NBRK0200): Contact Status, Output Relay Status, Outlet Status, Alarm Device Status, Memory Sensor Status, Memory Output Status, Memory Outlet Status, memory Beacon Status

EMS Status (for NBRK0200): EMS Hardware Status, Connection State

Hardware Probe (for NBRK0200): Sensor Id, Temperature, Relative Humidity, Connection State Code

Module Sensor (for NBRK0200): Sensor Name, Sensor location, Temperature, Relative Humidity, Connection State Code

 

SNMP Trap (V1, V2c)

SNMP Trap

See Event Types for more information about viewing the SNMP traps collected by FortiSIEM for this device.

Availability and Performance Monitoring

 

Event Types

In ADMIN > Device Support > Event Types, search for "NetBotz" to see the event types associated with this application or device. 

Event types for NetBotz NBRK0200

  • PH_DEV_MON_HW_STATUS

    [PH_DEV_MON_HW_STATUS]:[eventSeverity]=PHL_INFO,[fileName]=deviceNetBotz.cpp,[lineNumber]=1642,[hostName]=Unknown,[hostIpAddr]=10.62.97.61,[hwStatusCode]=2,[hwProbeStatus]=2,[hwInputContactStatus]=2,[hwOutputRelayStatus]=0,[hwOutletStatus]=2,[hwAlarmDeviceStatus]=0,[hwMemSensorStatus]=0,[hwMemOutputStatus]=2,[hwMemOutletStatus]=2,[hwMemBeaconStatus]=2,[phLogDetail]=
  • PH_DEV_MON_HW_EMS_STATUS

    [PH_DEV_MON_HW_EMS_STATUS]:[eventSeverity]=PHL_INFO,[fileName]=deviceNetBotz.cpp,[lineNumber]=1871,[hostName]=Unknown,[hostIpAddr]=10.62.97.61,[reptDevName]=Unknown,[emsHwStatus]=0,[phyMachConnectionStateCode]=2,[hwLogStatus]=1,[phLogDetail]=
  • PH_DEV_MON_HW_PROBE

    [PH_DEV_MON_HW_PROBE]:[eventSeverity]=PHL_INFO,[fileName]=deviceNetBotz.cpp,[lineNumber]=2100,[hostName]=Unknown,[hostIpAddr]=10.62.97.61,[envSensorLabel]=Sensor MM:4,[envTempDegF]=74,[envTempHighThreshDegF]=138,[envHumidityRel]=51,[envHumidityRelHighThresh]=90,[envHumidityRelLowThresh]=10,[serialNumber]=L3,[phyMachConnectionStateCode]=3,[maxTempThresh]=140,[minTempThresh]=32,[maxHumidityThresh]=99,[minHumidityThresh]=0,[phLogDetail]=
  • PH_DEV_MON_HW_MODULE_SENSOR

    [PH_DEV_MON_HW_MODULE_SENSOR]:[eventSeverity]=PHL_INFO,[fileName]=deviceNetBotz.cpp,[lineNumber]=2567,[hostName]=Unknown,[hostIpAddr]=10.62.97.61,[moduleNumber]=0,[envSensorId]=1,[envSensorLabel]=Sensor MM:1,[envSensorLoc]=Orland Park Server,[envTempDegF]=74,[envHumidityRel]=50,[phyMachConnectionStateCode]=1,[hwAlarmDevicetatus]=1,[phLogDetail]=

Rules

In RESOURCES > Rules, search for "NetBotz" in the main content panel Search... field to see the rules associated with this application or device. 

Reports

In RESOURCES > Reports, search for "NetBotz" in the main content panel Search... field to see the reports associated with this application or device. 

Configuration

SNMP

FortiSIEM uses SNMP to discover and monitor this device. Make sure SNMP is enabled for the device as directed in its product documentation. For more information, refer to sections "Discovery Settings" and "Setting Credentials" in the User Guide

SNMP Trap

FortiSIEM processes events from this device via SNMP traps sent by the device. Configure the device to send SNMP traps to FortiSIEM as directed in the device's product documentation, and FortiSIEM will parse the contents.

Setting Access Credentials

Set these Access Method Definition values to allow FortiSIEM to communicate with your device.

Setting Value
Name <set name>
Device Type APC NetBotz
Access Protocol See Access Credentials
Port See Access Credentials
Password config See Password Configuration