Allow multiple NetFlow collectors

FortiOS can be configured with a maximum of six NetFlow collectors. This also applies to multi-VDOM environments where a maximum of six NetFlow collectors can be used globally or on a per-VDOMs basis. This feature enables up to a maximum of six unique parallel NetFlow streams or transmissions per NetFlow sample to six different NetFlow collectors. The NetFlow collector configuration can only be configured in the CLI.

config system {netflow | vdom-netflow}
    config collectors
        edit <id>
            set collector-ip <IP address>
            set collector-port <port>
            set source-ip <IP address>
            set interface-select-method {auto | sdwan | specify}
            set interface <interface>
        next
    end
end

collector-ip	Enter the IPv4 or IPv6 address of the NetFlow collector that NetFlow agents added to interfaces in this VDOM send NetFlow datagrams to.
collector-port	Enter the UDP port number used for sending NetFlow datagrams; only configure if it is required by the NetFlow collector or network configuration (0 - 65535, default = 6343).
source-ip	Enter the source IPv4 or IPv6 address for the NetFlow agent.
interface-select-method	Specify how to select the outgoing interface to reach the server. auto: Set the outgoing interface automatically. sdwan: Set the outgoing interface by SD-WAN or policy routing rules. specify: Set the outgoing interface manually.
interface <interface>	Enter the outgoing interface to reach the server.

If the interface-select-method is set to auto, the outgoing interface that is used to send the sampled NetFlow traffic to the NetFlow collector is decided by the routing table lookup.

Example 1: Multiple NetFlow collectors in a non-VDOM environment

In this example, six NetFlow collectors are configured in a non-VDOM environment with NetFlow sampling on the port1 interface.

To configure multiple NetFlow collectors:

1. Configure the NetFlow collectors:

   config system netflow
      config collectors
      set active-flow-timeout 60
      set template-tx-timeout 60
           edit 1
               set collector-ip 172.16.200.155
               set collector-port 2055
               set source-ip 172.16.200.6
               set interface-select-method specify
               set interface "port1"
           next
           edit 2
               set collector-ip 10.1.100.59
               set collector-port 2056
               set source-ip 10.1.100.6
               set interface-select-method specify
               set interface "port2"
           next
           edit 3
               set collector-ip 172.18.60.80
               set collector-port 2057
               set interface-select-method specify
               set interface "port1"
           next
           edit 4
               set collector-ip "172.18.60.1"
               set collector-port 2058
           next
           edit 5
               set collector-ip "172.18.60.3"
               set collector-port 2059
           next
           edit 6
               set collector-ip "172.18.60.4"
               set collector-port 2060
           next
       end
   end

2. Configure NetFlow sampling on port1:

   config system interface
       edit port1
           set netflow-sampler both
       next
   end

3. Verify the NetFlow diagnostics.

   1. Verify the NetFlow configuration status:

      # diagnose test application sflowd 3
      
      ===== Netflow Vdom Configuration =====
      Global collector(s) active-timeout(seconds):60 inactive-timeout(seconds):15
          Collector id:1: 172.16.200.155[2055] source IP:172.16.200.6
          Collector id:2: 10.1.100.59[2056] source IP:10.1.100.6
          Collector id:3: 172.18.60.80[2057] source IP:
          Collector id:4: 172.18.60.1[2058] source IP:
          Collector id:5: 172.18.60.3[2059] source IP:
          Collector id:6: 172.18.60.4[2060] source IP:
      ____ vdom: root, index=0, is master, collector: disabled (use global config) (mgmt vdom)
         |_ coll_ip:172.16.200.155:2056,src_ip:172.16.200.6
         |_ coll_ip:10.1.100.59:2057,src_ip:10.1.100.6
         |_ coll_ip:172.18.60.80:2058,src_ip:172.16.200.6
         |_ coll_ip:172.18.60.1:2058,src_ip:172.16.200.6
         |_ coll_ip:172.18.60.3:2059,src_ip:172.16.200.6
         |_ coll_ip:172.18.60.4:2060,src_ip:172.16.200.6
         |_ seq_num:13 pkts/time to next template: 16/29
         |_ exported: Bytes:2533746, Packets:3911, Sessions:70 Flows:70
         |_ active_intf: 1
         |____ interface:port1 sample_direction:both device_index:9 snmp_index:3

   2. Verify the sampled NetFlow traffic packet capture:

      # diagnose sniffer packet any 'udp and port 2056 or 2057 or 2058' 4
      
      filters=[udp and port 2056 or 2057 or 2058]
      5.717060 port1 out 172.16.200.6.2472 -> 172.16.200.155.2055: udp 60   
      5.717068 port2 out 10.1.100.6.2472 -> 10.1.100.59.2056: udp 60   
      5.717075 port1 out 172.16.200.6.2472 -> 172.18.60.80.2057: udp 60   
      5.717078 port1 out 172.16.200.6.2472 -> 172.18.60.1.2058: udp 60   
      5.717081 port1 out 172.16.200.6.2472 -> 172.18.60.3.2059: udp 60   
      5.717085 port1 out 172.16.200.6.2472 -> 172.18.60.4.2060: udp 60   

Example 2: Multiple NetFlow collectors in a multi-VDOM environment

In this example, six NetFlow collectors are configured in a multi-VDOM environment globally and per VDOM. NetFlow sampling is on the port1 and port4 interfaces.

Please note it is not mandatory to set up per-VDOM NetFlow collectors in a multi-vdom environment. However, if you don’t enable per-VDOM collectors, the settings of the global NetFlow Collector will be used instead.

To configure multiple NetFlow collectors:

1. Configure the global NetFlow collectors:

   config system netflow
      config collectors
      set active-flow-timeout 60
      set template-tx-timeout 60
           edit 1
               set collector-ip 172.16.200.155
               set collector-port 2055
               set source-ip 172.16.200.6
               set interface-select-method specify
               set interface "port1"
           next
           edit 2
               set collector-ip 10.1.100.59
               set collector-port 2056
               set source-ip 10.1.100.6
               set interface-select-method specify
               set interface "port2"
           next
           edit 3
               set collector-ip 172.18.60.80
               set collector-port 2057
               set interface-select-method specify
               set interface "port1"
           next
           edit 4
               set collector-ip "172.18.60.1"
               set collector-port 2058
           next
           edit 5
               set collector-ip "172.18.60.3"
               set collector-port 2059
           next
           edit 6
               set collector-ip "172.18.60.4"
               set collector-port 2060
           next
       end
   end

2. Configure the per-VDOM NetFlow collectors:

   config system vdom-netflow
       set vdom-netflow enable
       config collectors
           edit 1
               set collector-ip "172.10.100.101"
               set collector-port 2059
           next
           edit 2
               set collector-ip "172.10.100.102"
               set collector-port 2060
           next
           edit 3
               set collector-ip "172.10.100.103"
               set collector-port 2061
           next
           edit 4
               set collector-ip "172.10.100.104"
               set collector-port 2062
           next
           edit 5
               set collector-ip "172.10.100.105"
               set collector-port 2063
           next
           edit 6
               set collector-ip "172.10.100.106"
               set collector-port 2064
           next
       end
   end

3. Configure NetFlow sampling on port1 and port4:

   config system interface
       edit port1
           set netflow-sampler both
       next
       edit port4
           set netflow-sampler both
       next
   end

   In a multi-VDOM environment, ensure the interface selected for NetFlow sampling is in the same VDOM as the per-VDOM NetFlow collector. For global NetFlow collectors, the interface selected for NetFlow sampling should be in the management VDOM.

4. Verify the NetFlow diagnostics.

   1. Verify the NetFlow configuration status:

      # diagnose test application sflowd 3
      
      ===== Netflow Vdom Configuration =====
      Global collector(s) active-timeout(seconds):60 inactive-timeout(seconds):15
          Collector id:1: 172.16.200.155[2055] source IP:172.16.200.6
          Collector id:2: 10.1.100.59[2056] source IP:10.1.100.6
          Collector id:3: 172.18.60.80[2057] source IP:
          Collector id:4: 172.18.60.1[2058] source IP:
          Collector id:5: 172.18.60.3[2059] source IP:
          Collector id:6: 172.18.60.4[2060] source IP:
      ____ vdom: root, index=0, is master, collector: disabled (use global config) (mgmt vdom)
         |_ coll_ip:172.16.200.155:2056,src_ip:172.16.200.6
         |_ coll_ip:10.1.100.59:2057,src_ip:10.1.100.6
         |_ coll_ip:172.18.60.80:2058,src_ip:172.16.200.6
         |_ coll_ip:172.18.60.1:2058,src_ip:172.16.200.6
         |_ coll_ip:172.18.60.3:2059,src_ip:172.16.200.6
         |_ coll_ip:172.18.60.4:2060,src_ip:172.16.200.6
         |_ seq_num:13 pkts/time to next template: 16/29
         |_ exported: Bytes:2533746, Packets:3911, Sessions:70 Flows:70
         |_ active_intf: 1
         |____ interface:port1 sample_direction:both device_index:9 snmp_index:3
      ____ vdom: vdom1, index=1, is master, collector: enabled
         |_ coll_ip:172.10.100.101:2059,src_ip:20.1.100.111
         |_ coll_ip:172.10.100.102:2060,src_ip:20.1.100.111
         |_ coll_ip:172.10.100.103:2061,src_ip:20.1.100.111
         |_ coll_ip:172.10.100.104:2062,src_ip:20.1.100.111
         |_ coll_ip:172.10.100.105:2063,src_ip:20.1.100.111
         |_ coll_ip:172.10.100.106:2064,src_ip:20.1.100.111
         |_ seq_num:27 pkts/time to next template: 15/18
         |_ exported: Bytes:5040, Packets:60, Sessions:6 Flows:6
         |_ active_intf: 1
         |____ interface:port4 sample_direction:both device_index:12 snmp_index:6

   2. Verify the sampled NetFlow traffic packet capture:

      # diagnose sniffer packet any 'udp and port 2059 or 2060 or 2061 or 2062 or 2063 or 2064' 4
      
      filters=[udp and port 2059 or 2060 or 2061 or 2062 or 2063 or 2064]
      7.005812 port4 out 20.1.100.111.2472 -> 172.10.100.101.2059: udp 60
      7.005821 port4 out 20.1.100.111.2472 -> 172.10.100.102.2060: udp 60
      7.005826 port4 out 20.1.100.111.2472 -> 172.10.100.103.2061: udp 60
      7.005830 port4 out 20.1.100.111.2472 -> 172.10.100.104.2062: udp 60
      7.005834 port4 out 20.1.100.111.2472 -> 172.10.100.105.2063: udp 60
      7.005838 port4 out 20.1.100.111.2472 -> 172.10.100.106.2064: udp 60