Version:

Version:

Version:

Version:

Version:

Version:

Version:

Version:


Table of Contents

Hardware Acceleration

Displaying NP7 HPE configuration and status information

You can use the following diagnose command to display NP7 HPE configuration and status information for one of the NP7 processors in your FortiGate.

diagnose npu np7 hpe 2

[NP7_2]
Queue  Type         NPU-min   NPU-max   CFG-min(pps) CFG-max(pps) Pkt-credit
0      high-priority39731     39731     40000        40000        0         
0      TCP-syn      39731     39731     40000        40000        0         
0      TCP-synack   39731     39731     40000        40000        0         
0      TCP-finrst   39731     39731     40000        40000        0         
0      TCP          39731     39731     40000        40000        0         
0      UDP          39731     39731     40000        40000        0         
0      ICMP         19865     19865     20000        20000        0         
0      SCTP         19865     19865     20000        20000        0         
0      ESP          19865     19865     20000        20000        0         
0      IP-Frag      19865     19865     20000        20000        0         
0      IP_others    19865     19865     20000        20000        0         
0      ARP          19865     19865     20000        20000        0         
0      l2_others    19865     19865     20000        20000        0         
0      all-protocol 39731     39731     40000        40000        0         
---------------------------------------------------------------------------
HPE HW pkt_credit:11080 , tsref_inv:50000, tsref_gap:32, hpe_refskip:0 , hif->nr_ring:40

Note:
 NPU-min and NPU-max: The register reading of max and min value for each queue in NPU.
 CFG-min(pps): the setting value of hpe configuration in CLI command and
               it is packet per second rate limit for each host rx queue of NPU.
 CFG-max(pps): The value is CFG-min of hpe configuration in CLI command.

Displaying NP7 HPE configuration and status information

You can use the following diagnose command to display NP7 HPE configuration and status information for one of the NP7 processors in your FortiGate.

diagnose npu np7 hpe 2

[NP7_2]
Queue  Type         NPU-min   NPU-max   CFG-min(pps) CFG-max(pps) Pkt-credit
0      high-priority39731     39731     40000        40000        0         
0      TCP-syn      39731     39731     40000        40000        0         
0      TCP-synack   39731     39731     40000        40000        0         
0      TCP-finrst   39731     39731     40000        40000        0         
0      TCP          39731     39731     40000        40000        0         
0      UDP          39731     39731     40000        40000        0         
0      ICMP         19865     19865     20000        20000        0         
0      SCTP         19865     19865     20000        20000        0         
0      ESP          19865     19865     20000        20000        0         
0      IP-Frag      19865     19865     20000        20000        0         
0      IP_others    19865     19865     20000        20000        0         
0      ARP          19865     19865     20000        20000        0         
0      l2_others    19865     19865     20000        20000        0         
0      all-protocol 39731     39731     40000        40000        0         
---------------------------------------------------------------------------
HPE HW pkt_credit:11080 , tsref_inv:50000, tsref_gap:32, hpe_refskip:0 , hif->nr_ring:40

Note:
 NPU-min and NPU-max: The register reading of max and min value for each queue in NPU.
 CFG-min(pps): the setting value of hpe configuration in CLI command and
               it is packet per second rate limit for each host rx queue of NPU.
 CFG-max(pps): The value is CFG-min of hpe configuration in CLI command.