Fortinet Document Library

Version:


Table of Contents

CLI Reference

6.0.6
Download PDF
Copy Link

system modem

Introduction.

config system modem
    set status {enable | disable}   Enable/disable Modem support (equivalent to bringing an interface up or down).
    set pin-init {string}   AT command to set the PIN (AT+PIN=<pin>). size[127]
    set network-init {string}   AT command to set the Network name/type (AT+COPS=<mode>,[<format>,<oper>[,<AcT>]]). size[127]
    set lockdown-lac {string}   Allow connection only to the specified Location Area Code (LAC). size[127]
    set mode {standalone | redundant}   Set MODEM operation mode to redundant or standalone.
            standalone  Standalone.
            redundant   Redundant for an interface.
    set auto-dial {enable | disable}   Enable/disable auto-dial after a reboot or disconnection.
    set dial-on-demand {enable | disable}   Enable/disable to dial the modem when packets are routed to the modem interface.
    set idle-timer {integer}   MODEM connection idle time (1 - 9999 min, default = 5). range[1-9999]
    set redial {option}   Redial limit (1 - 10 attempts, none = redial forever).
            none  Forever.
            1     One attempt.
            2     Two attempts.
            3     Three attempts.
            4     Four attempts.
            5     Five attempts.
            6     Six attempts.
            7     Seven attempts.
            8     Eight attempts.
            9     Nine attempts.
            10    Ten attempts.
    set reset {integer}   Number of dial attempts before resetting modem (0 = never reset). range[0-10]
    set holddown-timer {integer}   Hold down timer in seconds (1 - 60 sec). range[1-60]
    set connect-timeout {integer}   Connection completion timeout (30 - 255 sec, default = 90). range[30-255]
    set interface {string}   Name of redundant interface. size[63] - datasource(s): system.interface.name
    set wireless-port {integer}   Enter wireless port number, 0 for default, 1 for first port, ... (0 - 4294967295, default = 0) range[0-4294967295]
    set dont-send-CR1 {enable | disable}   Do not send CR when connected (ISP1).
    set phone1 {string}   Phone number to connect to the dialup account (must not contain spaces, and should include standard special characters). size[63]
    set dial-cmd1 {string}   Dial command (this is often an ATD or ATDT command). size[63]
    set username1 {string}   User name to access the specified dialup account. size[63]
    set passwd1 {password_string}   Password to access the specified dialup account. size[128]
    set extra-init1 {string}   Extra initialization string to ISP 1. size[127]
    set peer-modem1 {generic | actiontec | ascend_TNT}   Specify peer MODEM type for phone1.
            generic     All other modem type.
            actiontec   ActionTec modem.
            ascend_TNT  Ascend TNT modem.
    set ppp-echo-request1 {enable | disable}   Enable/disable PPP echo-request to ISP 1.
    set authtype1 {pap | chap | mschap | mschapv2}   Allowed authentication types for ISP 1.
            pap       PAP
            chap      CHAP
            mschap    MSCHAP
            mschapv2  MSCHAPv2
    set dont-send-CR2 {enable | disable}   Do not send CR when connected (ISP2).
    set phone2 {string}   Phone number to connect to the dialup account (must not contain spaces, and should include standard special characters). size[63]
    set dial-cmd2 {string}   Dial command (this is often an ATD or ATDT command). size[63]
    set username2 {string}   User name to access the specified dialup account. size[63]
    set passwd2 {password_string}   Password to access the specified dialup account. size[128]
    set extra-init2 {string}   Extra initialization string to ISP 2. size[127]
    set peer-modem2 {generic | actiontec | ascend_TNT}   Specify peer MODEM type for phone2.
            generic     All other modem type.
            actiontec   ActionTec modem.
            ascend_TNT  Ascend TNT modem.
    set ppp-echo-request2 {enable | disable}   Enable/disable PPP echo-request to ISP 2.
    set authtype2 {pap | chap | mschap | mschapv2}   Allowed authentication types for ISP 2.
            pap       PAP
            chap      CHAP
            mschap    MSCHAP
            mschapv2  MSCHAPv2
    set dont-send-CR3 {enable | disable}   Do not send CR when connected (ISP3).
    set phone3 {string}   Phone number to connect to the dialup account (must not contain spaces, and should include standard special characters). size[63]
    set dial-cmd3 {string}   Dial command (this is often an ATD or ATDT command). size[63]
    set username3 {string}   User name to access the specified dialup account. size[63]
    set passwd3 {password_string}   Password to access the specified dialup account. size[128]
    set extra-init3 {string}   Extra initialization string to ISP 3. size[127]
    set peer-modem3 {generic | actiontec | ascend_TNT}   Specify peer MODEM type for phone3.
            generic     All other modem type.
            actiontec   ActionTec modem.
            ascend_TNT  Ascend TNT modem.
    set ppp-echo-request3 {enable | disable}   Enable/disable PPP echo-request to ISP 3.
    set altmode {enable | disable}   Enable/disable altmode for installations using PPP in China.
    set authtype3 {pap | chap | mschap | mschapv2}   Allowed authentication types for ISP 3.
            pap       PAP
            chap      CHAP
            mschap    MSCHAP
            mschapv2  MSCHAPv2
    set traffic-check {enable | disable}   Enable/disable traffic-check.
    set action {dial | stop | none}   Dial up/stop MODEM.
            dial  Dial up number.
            stop  Stop dialup.
            none  No action.
    set distance {integer}   Distance of learned routes (1 - 255, default = 1). range[1-255]
    set priority {integer}   Priority of learned routes (0 - 4294967295, default = 0). range[0-4294967295]
end

system modem

Introduction.

config system modem
    set status {enable | disable}   Enable/disable Modem support (equivalent to bringing an interface up or down).
    set pin-init {string}   AT command to set the PIN (AT+PIN=<pin>). size[127]
    set network-init {string}   AT command to set the Network name/type (AT+COPS=<mode>,[<format>,<oper>[,<AcT>]]). size[127]
    set lockdown-lac {string}   Allow connection only to the specified Location Area Code (LAC). size[127]
    set mode {standalone | redundant}   Set MODEM operation mode to redundant or standalone.
            standalone  Standalone.
            redundant   Redundant for an interface.
    set auto-dial {enable | disable}   Enable/disable auto-dial after a reboot or disconnection.
    set dial-on-demand {enable | disable}   Enable/disable to dial the modem when packets are routed to the modem interface.
    set idle-timer {integer}   MODEM connection idle time (1 - 9999 min, default = 5). range[1-9999]
    set redial {option}   Redial limit (1 - 10 attempts, none = redial forever).
            none  Forever.
            1     One attempt.
            2     Two attempts.
            3     Three attempts.
            4     Four attempts.
            5     Five attempts.
            6     Six attempts.
            7     Seven attempts.
            8     Eight attempts.
            9     Nine attempts.
            10    Ten attempts.
    set reset {integer}   Number of dial attempts before resetting modem (0 = never reset). range[0-10]
    set holddown-timer {integer}   Hold down timer in seconds (1 - 60 sec). range[1-60]
    set connect-timeout {integer}   Connection completion timeout (30 - 255 sec, default = 90). range[30-255]
    set interface {string}   Name of redundant interface. size[63] - datasource(s): system.interface.name
    set wireless-port {integer}   Enter wireless port number, 0 for default, 1 for first port, ... (0 - 4294967295, default = 0) range[0-4294967295]
    set dont-send-CR1 {enable | disable}   Do not send CR when connected (ISP1).
    set phone1 {string}   Phone number to connect to the dialup account (must not contain spaces, and should include standard special characters). size[63]
    set dial-cmd1 {string}   Dial command (this is often an ATD or ATDT command). size[63]
    set username1 {string}   User name to access the specified dialup account. size[63]
    set passwd1 {password_string}   Password to access the specified dialup account. size[128]
    set extra-init1 {string}   Extra initialization string to ISP 1. size[127]
    set peer-modem1 {generic | actiontec | ascend_TNT}   Specify peer MODEM type for phone1.
            generic     All other modem type.
            actiontec   ActionTec modem.
            ascend_TNT  Ascend TNT modem.
    set ppp-echo-request1 {enable | disable}   Enable/disable PPP echo-request to ISP 1.
    set authtype1 {pap | chap | mschap | mschapv2}   Allowed authentication types for ISP 1.
            pap       PAP
            chap      CHAP
            mschap    MSCHAP
            mschapv2  MSCHAPv2
    set dont-send-CR2 {enable | disable}   Do not send CR when connected (ISP2).
    set phone2 {string}   Phone number to connect to the dialup account (must not contain spaces, and should include standard special characters). size[63]
    set dial-cmd2 {string}   Dial command (this is often an ATD or ATDT command). size[63]
    set username2 {string}   User name to access the specified dialup account. size[63]
    set passwd2 {password_string}   Password to access the specified dialup account. size[128]
    set extra-init2 {string}   Extra initialization string to ISP 2. size[127]
    set peer-modem2 {generic | actiontec | ascend_TNT}   Specify peer MODEM type for phone2.
            generic     All other modem type.
            actiontec   ActionTec modem.
            ascend_TNT  Ascend TNT modem.
    set ppp-echo-request2 {enable | disable}   Enable/disable PPP echo-request to ISP 2.
    set authtype2 {pap | chap | mschap | mschapv2}   Allowed authentication types for ISP 2.
            pap       PAP
            chap      CHAP
            mschap    MSCHAP
            mschapv2  MSCHAPv2
    set dont-send-CR3 {enable | disable}   Do not send CR when connected (ISP3).
    set phone3 {string}   Phone number to connect to the dialup account (must not contain spaces, and should include standard special characters). size[63]
    set dial-cmd3 {string}   Dial command (this is often an ATD or ATDT command). size[63]
    set username3 {string}   User name to access the specified dialup account. size[63]
    set passwd3 {password_string}   Password to access the specified dialup account. size[128]
    set extra-init3 {string}   Extra initialization string to ISP 3. size[127]
    set peer-modem3 {generic | actiontec | ascend_TNT}   Specify peer MODEM type for phone3.
            generic     All other modem type.
            actiontec   ActionTec modem.
            ascend_TNT  Ascend TNT modem.
    set ppp-echo-request3 {enable | disable}   Enable/disable PPP echo-request to ISP 3.
    set altmode {enable | disable}   Enable/disable altmode for installations using PPP in China.
    set authtype3 {pap | chap | mschap | mschapv2}   Allowed authentication types for ISP 3.
            pap       PAP
            chap      CHAP
            mschap    MSCHAP
            mschapv2  MSCHAPv2
    set traffic-check {enable | disable}   Enable/disable traffic-check.
    set action {dial | stop | none}   Dial up/stop MODEM.
            dial  Dial up number.
            stop  Stop dialup.
            none  No action.
    set distance {integer}   Distance of learned routes (1 - 255, default = 1). range[1-255]
    set priority {integer}   Priority of learned routes (0 - 4294967295, default = 0). range[0-4294967295]
end