Common SMM CLI operations

The following table lists many of the operations you can perform from the SMM CLI and the commands you use to perform them. Only a subset of these commands are available on the passive SMM as indicated below. Also, the <slot> option is not available on the passive SMM.

Action	SMC CLI Commands	IPMI Commands
Log into the CLI.	Ctrl-R	N/A
Log out of the CLI. Available on the passive module.	exit (followed by Ctrl-R)	N/A
Display all commands. Available on the passive module.	help	help
Display information about all SMC firmware in the chassis.	info	mc info
Display SMC device ID, Build Date/Number, SMC firmware information, address info, entity map for the device in the slot. Available on the passive module.	info <slot>	N/A
Switching active SMM. The active SMM becomes passive and the passive becomes active. Available on the passive module.	smm_switch	N/A
Display status, power budget and hot swap state for all modules. Available on the passive module.	status	N/A
List the IPMI channels.	channel list	channel info [<channel-number>]
Change the SDI verbosity level. <level> can be: 0: Alerts + Errors 1: Alerts + Errors + Verbose + Low-Level Errors 2: Alerts + Errors + Verbose + Low-Level Errors + PI traffic 3: Alerts + Errors + Verbose + Low-Level Errors + PI traffic + IPMB traffic + LAN Interface traffic 4: Same as 3	verbose <level>	N/A
Display the SMM time. Available on the passive module.	time get	sel time get
Set the SMM time. Available on the passive module.	time set <yyy/mm/dd hh:mm:ss>	sel time set <yyy/mm/dd hh:mm:ss>
Synchronize all module SMC times.	time sync	N/A
List SMM user accounts. Available on the passive module.	user list	user list [<channel number>]
Disable a user account. Available on the passive module.	user disable <user-id>	user disable <user-id>
Enable a user account. Available on the passive module.	user enable <user-id>	user enable <user-id>
Set a user account user name. Available on the passive module.	user set name <user-id> <name>	user set name <user-id> <name>
Set a user account password. Available on the passive module.	user set password <user-id> <password>	user set password <user-id> <password>
Set the privilege level that a user account has for a specified session-based IPMI <channel>. If a <channel> is not specified the privilege level is set for all IPMI channels. Available on the passive module.	user priv <user-id> {callback | user | operator | administrator | no_access} [<channel>]	user priv <user id> <privilege level> [<channel number>]
View a summary of users.	N/A	user summary
User test command.	N/A	user test
Display the SMM serial interface settings. Available on the passive module.	serial print	N/A
Set the SDI baud rate. Available on the passive module.	serial set sdi baud <speed>	N/A
Set the sniff baud rate when the console is disabled. Available on the passive module.	serial set sdi default_sniff_baud <speed>	N/A
Enable a console connection from the SMM to another module.	serial set sdi enable <slot>	N/A
Disable the console connection between the SMM and another module. Available on the passive module.	serial set sdi disable <slot>	N/A
Cold or warm reset a module.	mc reset <slot> cold mc reset <slot> warm	mc reset cold mc reset warm
Run a module self test.	N/A	mc selftest
Power on a module.	fru activate <slot> [<fruid>]	picmg activate
Power off a module.	fru deactivate <slot> [<fruid>]	picmg deactivate
Reset a module.	fru reset <slot> [<fruid>]	picmg reset
Power cycle the chassis	N/A	chassis power cycle
Get chassis sttatus	N/A	chassis status
Display the LAN configuration. Available on the passive module.	lan print <channel>
Set LAN configuration. The kgkey and krkey options are used for RCMP+.	lan set <channel> ipaddr <ip> [<netmask>] lan set <channel> macaddr <mac> lan set <channel> defgw ipaddr <ip> lan set <channel> defgw macaddr <mac> lan set <channel> kgkey <value> lan set <channel> krkey <value>	lan set help (use this command to display online help for LAN settings)
Enable or disable all LAN interfaces.	lan disable <channel> lan enable <channel>	fortinetoem param set 0 1 fortinetoem param set 0 0
Set fan levels. Change or switch the active fan set.	fan_min_level <level> fan_max_level <level> <level> range is 0 - 20.	N/A
Change LED settings.	N/A	picmg led set help (use this command to display online help for LED settings)
Display HPM.1 status.	N/A	hpm check
Run an HPM.1 upgrade.	N/A	hpm upgrade <.img> hpm upgrade <.img> all activate