Chassis hardware information
This section introduces FortiGate-7040E hardware components and accessories including power requirements and FIMs and FPMs that can be installed in the chassis.
Shipping components
The FortiGate-7040E chassis ships pre-assembled with the following components:
- The 6U FortiGate-7040E chassis.
- Two FIMs.
- Two FPMs.
- One System Management Module (SMM) in the front of the chassis. (The SMM is not field replacable. If the it fails, you must RMA the chassis. The chassis will continue to operate without a functioning SMM.)
- Three Power Supply Units (PSUs) installed in the back of the chassis.
- Three cooling fan trays installed in the back of the chassis.
- One protective front panel installed in the chassis to protect internal chassis components. This panel must be removed before installing FIMs and FPMs.
- Four FIM or FPM blank panels that can be installed in empty chassis slots. The blank panels are part of the chassis package and all blank panels should be kept available in case an FIM or an FPM needs to be removed from the chassis.
- Three power cords with C15 power connectors.
- Four power cord management clamps.
- One set of 4-post rack mounting components.
- One set of 2-post rack mounting components.
- One pair of cable management side brackets.
- Two front mounting brackets.
- Twenty M4x6 flat-head screws.
- Ten M4x8 large head pan-head screws.
- Six rubber feet.
- Two USB to RJ-45 RS-232 console cables.
- One RJ-45 Ethernet cable.
Optional accessories and replacement parts
The following optional accessories can be ordered separately:
| SKU | Description |
|---|---|
| FG-7040E-FAN | FortiGate-7040E fan tray. |
| FG-7040E-PS-AC | 1500W AC power supply units (PSUs) for the FortiGate-7040E. |
| FG-7040E-CHASSIS | FortiGate-7040E chassis including 1x SMM, 3x fan trays, and 3x AC PSUs. |
You can also order the following:
- Additional FIMs and FPMs.
- Transceivers.
- DC PSUs (Each PSU ships with a set of two 8 AWG DC power cables and six extra DC terminal rings. The cables are 3 meters (9.84 ft.) long. You can use the DC terminal rings to make custom DC cables.)
- Air Filter kit.
- FPM and FIM single slot cover trays to be installed in empty chassis slots.
Physical description of the FortiGate-7040E chassis
The FortiGate-7040E chassis is a 6U chassis that can be installed in a standard 19-inch rack. The following table describes the physical characteristics of the FortiGate-7040E chassis.
| Dimensions (H x W x D) | 10.5 x 17.3 x 25.6 in (264 x 440 x 650 mm) |
| Chassis weight completely assembled with FIM and FPM modules installed | 150.3 lbs (68.2 kg) |
| Operating temperature | 32 to 104°F (0 to 40°C) |
| Storage temperature | -31 to 158°F (-35 to 70°C) |
| Relative humidity | 10% to 90% non-condensing |
| Noise level | 63db |
| Input voltage range | 100 to 240 VAC (50 to 60 Hz) |
| Power support rating | 1500W@240VAC and 1200W@120VAC |
| Supplied power supply units (PSUs) | 3 (for 2+1 redundancy) |
| Max power supply units (PSUs) | 4 (for 2+2 redundancy) |
| Max power consumption (two FPM-7620Es) | 2400W |
| Average power consumption (two FPM-7620Es) | 1800W |
| Max power consumption (two FPM-7630Es) | 2460W |
| Average power consumption (two FPM-7630Es) | 1840W |
| Max current | 110V/15A |
| Heat dissipation (two FPM-7620Es) | 8189 BTU/hr |
| Heat dissipation (two FPM-7630Es) | 8456 BTU/h |
| Joules/hr | 8632 KJ/hr |