Version:

Version:

Version:

Version:

Version:


Table of Contents

FortiGate-7000E Handbook

FortiGate-7000 FGSP

FortiGate-7000 supports the FortiGate Session Life Support Protocol (FGSP) (also called standalone session sync) to synchronize sessions among up to four FortiGate-7000s. All of the FortiGate-7000s must be the same model and running the same firmware and must have their own network configuration (interface IPs, routing, and so on). FGSP synchronizes individual VDOM sessions. All of the devices in an FGSP deployment must include the VDOMs to be synchronized and for each device the VDOMs must have the same firewall configuration.

For details about FGSP for FortiOS 6.0, see: FortiOS 6.0 Handbook: FGSP.

FortiGate-7000 FGSP support has the following limitations:

  • FortiGate-7000 FGSP can use the M1 or M2 interface for session synchronization. FortiGate-7000 FGSP does not support using a LAG consisting of the M1 and M2 interfaces for session synchronization.
  • To use the M1 or the M2 interface for session synchronization, you must give the interface an IP address and optionally set up routing for the interface as required. Ideally the session synchronization interface of each FortiGate-7000 would be on the same network and that network would only be used for session synchronization traffic. However, you can configure routing to send session synchronization traffic between networks. NAT between session synchronization interfaces is not supported.
  • You can't use data interfaces for FGSP session synchronization.
  • You can use configuration synchronization to synchronize the configurations of the FortiGate-7000s in the FGSP deployment (see Standalone configuration synchronization). You can use the M1 and M2 interfaces for configuration synchronization. You can also configure the FortiGate-7000s separately or use FortiManager to keep key parts of the configuration, such as security policies, synchronized.
  • FortiGate-7000 FGSP doesn't support setting up IPv6 session filters using the config session-sync-filter option.
  • FGSP doesn't synchronize ICMP sessions when ICMP load balancing is set to to-master. If you want to synchronize ICMP sessions, set ICMP load balancing to either src-ip, dst-ip, or src-dst-ip. See ICMP load balancing for more information.
  • Asymmetric IPv6 SCTP traffic sessions are not supported. These sessions are dropped.
  • Inter-cluster session synchronization, or FGSP between FGCP clusters, is not supported.
  • FGSP IPsec tunnel synchronization is not supported.
  • Fragmented packet synchronization is not supported.

FortiGate-7000 FGSP

FortiGate-7000 supports the FortiGate Session Life Support Protocol (FGSP) (also called standalone session sync) to synchronize sessions among up to four FortiGate-7000s. All of the FortiGate-7000s must be the same model and running the same firmware and must have their own network configuration (interface IPs, routing, and so on). FGSP synchronizes individual VDOM sessions. All of the devices in an FGSP deployment must include the VDOMs to be synchronized and for each device the VDOMs must have the same firewall configuration.

For details about FGSP for FortiOS 6.0, see: FortiOS 6.0 Handbook: FGSP.

FortiGate-7000 FGSP support has the following limitations:

  • FortiGate-7000 FGSP can use the M1 or M2 interface for session synchronization. FortiGate-7000 FGSP does not support using a LAG consisting of the M1 and M2 interfaces for session synchronization.
  • To use the M1 or the M2 interface for session synchronization, you must give the interface an IP address and optionally set up routing for the interface as required. Ideally the session synchronization interface of each FortiGate-7000 would be on the same network and that network would only be used for session synchronization traffic. However, you can configure routing to send session synchronization traffic between networks. NAT between session synchronization interfaces is not supported.
  • You can't use data interfaces for FGSP session synchronization.
  • You can use configuration synchronization to synchronize the configurations of the FortiGate-7000s in the FGSP deployment (see Standalone configuration synchronization). You can use the M1 and M2 interfaces for configuration synchronization. You can also configure the FortiGate-7000s separately or use FortiManager to keep key parts of the configuration, such as security policies, synchronized.
  • FortiGate-7000 FGSP doesn't support setting up IPv6 session filters using the config session-sync-filter option.
  • FGSP doesn't synchronize ICMP sessions when ICMP load balancing is set to to-master. If you want to synchronize ICMP sessions, set ICMP load balancing to either src-ip, dst-ip, or src-dst-ip. See ICMP load balancing for more information.
  • Asymmetric IPv6 SCTP traffic sessions are not supported. These sessions are dropped.
  • Inter-cluster session synchronization, or FGSP between FGCP clusters, is not supported.
  • FGSP IPsec tunnel synchronization is not supported.
  • Fragmented packet synchronization is not supported.