Fortinet black logo

FortiGate-7000 Handbook

FortiGate-7000 v5.6.11 special features and limitations

Copy Link
Copy Doc ID 42931b88-172e-11ec-8c53-00505692583a:566453
Download PDF

FortiGate-7000 v5.6.11 special features and limitations

This section describes special features and limitations for FortiGate-7000 v5.6.11.

Managing the FortiGate-7000

Management is only possible through the MGMT1 to MGMT4 front panel management interfaces. By default the MGMT1 to MGMT4 interfaces of the FIMs in slot 1 and slot 2 are in a single static aggregate interface named mgmt with IP address 192.168.1.99. You manage the FortiGate-7000 by connecting any one of these eight interfaces to your network, opening a web browser and browsing to the management IP address. For a factory default configuration, browse to https://192.168.1.99.

Note The FortiGate-7030E has one FIM and the MGMT1 to MGMT4 interfaces of that module are the only interfaces in the aggregate interface.

Default management VDOM

By default the FortiGate-7000 configuration includes a management VDOM named mgmt-vdom. For the FortiGate-7000 system to operate normally you should not change the configuration of this VDOM and this VDOM should always be the management VDOM. You should also not add or remove interfaces from this VDOM.

You have full control over the configurations of other FortiGate-7000 VDOMs.

Default Security Fabric configuration

The FortiGate-7000 uses the Security Fabric for communication and synchronization among FIMs and FPMs. Changing the default Security Fabric configuration could disrupt this communication and affect system performance.

Default Security Fabric configuration:

config system csf

set status enable

set configuration-sync local

set management-ip 0.0.0.0

set management-port 0

end

For the FortiGate-7000 to operate normally, you must not change the Security Fabric configuration.

Maximum number of LAGs and interfaces per LAG

FortiGate-7000 systems support up to 16 link aggregation groups (LAGs). This includes both normal link aggregation groups and redundant interfaces and including the redundant interface that contains the M1 to M4 management interfaces. A FortiGate-7000 LAG can include up to 20 interfaces.

Firewall

TCP sessions with NAT enabled that are expected to be idle for more than the distributed processing normal TCP timer (which is 3605 seconds) should only be distributed to the master FPM using a flow rule. You can configure the distributed normal TCP timer using the following command:

config system global

set dp-tcp-normal-timer <timer>

end

UDP sessions with NAT enabled that are expected to be idle for more than the distributed processing normal UDP timer should only be distributed to the primary FPM using a flow rule.

IP multicast

IPv4 and IPv6 Multicast traffic is only sent to the primary FPM (usually the FPM in slot 3). This is controlled by the following configuration:

config load-balance flow-rule

edit 18

set status enable

set vlan 0

set ether-type ipv4

set src-addr-ipv4 0.0.0.0 0.0.0.0

set dst-addr-ipv4 224.0.0.0 240.0.0.0

set protocol any

set action forward

set forward-slot master

set priority 5

set comment "ipv4 multicast"

next

edit 19

set status enable

set vlan 0

set ether-type ipv6

set src-addr-ipv6 ::/0

set dst-addr-ipv6 ff00::/8

set protocol any

set action forward

set forward-slot master

set priority 5

set comment "ipv6 multicast"

end

High availability

Only the M1 and M2 interfaces are used for the HA heartbeat communication. For information on how to set up HA heartbeat communication using the M1 and M2 interfaces, see Connect the M1 and M2 interfaces for HA heartbeat communication

The following FortiOS HA features are not supported or are supported differently by FortiGate-7000 v5.6.11:

  • Active-active HA is not supported.
  • The range for the HA group-id is 0 to 31.
  • Failover logic for FortiGate-7000 HA is not the same as FGCP for other FortiGate clusters.
  • HA heartbeat configuration is specific to FortiGate-7000 systems and differs from standard HA.
  • FortiGate Session Life Support Protocol (FGSP) HA (also called standalone session synchronization) is not supported.
  • FortiGate-7000 HA does not support the route-ttl, route-wait, and route-hold options for tuning route synchronization between FortiGate-7000s.
  • VLAN monitoring using the config system ha-monitor command is not supported.

Use of the diagnose sys ha checksum cluster command not recommended

The FortiGate-7000 uses a custom FGCP HA implementation and the diagnose sys ha checksum cluster command may show incorrect checksums so can't be used to check cluster synchronization. Instead you can log into the primary FIM of each FortiGate-7000 in the cluster and use the diagnose sys confsync showcsum and compare the results.

Shelf manager module

It is not possible to access SMM CLI using Telnet or SSH. Only console access is supported using the chassis front panel console ports as described in the FortiGate-7000 system guide.

For monitoring purpose, IPMI over IP is supported on SMM Ethernet ports. See your FortiGate-7000 system guide for details.

FortiOS features not supported by FortiGate-7000 v5.6.11

The following mainstream FortiOS 5.6.11 features are not supported by the FortiGate-7000 v5.6.11:

  • Hardware switch
  • Usage-based ECMP load balancing is not supported. If the config system settings v4-ecmp-mode option is set to usage-based, all traffic uses the first ECMP route instead of being load balanced among all ECMP routes. All other ECMP load balancing options are supported, including source-ip-based, weight-based, and source-dest-ip-based.
  • Switch controller
  • WiFi controller
  • WAN load balancing (SD-WAN)
  • IPv4 over IPv6, IPv6 over IPv4, IPv6 over IPv6 features
  • GRE tunneling is only supported after creating a load balance flow rule, for example:

    config load-balance flow-rule

    edit 0

    set status enable

    set vlan 0

    set ether-type ip

    set protocol gre

    set action forward

    set forward-slot master

    set priority 3

    end

  • Hard disk features including, WAN optimization, web caching, explicit proxy content caching, disk logging, and GUI-based packet sniffing.
  • The FortiGate-7000 platform only supports quarantining files to FortiAnalyzer.
  • Log messages should be sent only using the management aggregate interface
  • The FortiGate-7000 does not support configuring dedicated management interfaces using the config system dedicated-mgmt command or by enabling the dedicated-to management interface option.

IPsec VPN tunnels terminated by the FortiGate-7000

For a list of new FortiOS 5.6 FortiGate-7000 IPsec VPN features and a list of IPsec VPN features not supported by FortiOS 5.6 FortiGate-7000 IPsec VPN, see New IPsec VPN features.

SSL VPN

Sending all SSL VPN sessions to the primary FPM is recommended. You can do this by:

  • Creating a flow rule that sends all sessions that use the SSL VPN destination port and IP address to the primary FPM.
  • Creating flow rules that send all sessions that use the SSL VPN IP pool addresses to the primary FPM.

For more information about FortiGate-7000 SSL VPN support, see SSL VPN load balancing.

Traffic shaping and DDoS policies

Each FPM applies traffic shaping and DDoS quotas independently. Because of load-balancing, this may allow more traffic than expected.

FortiGuard web filtering and spam filtering queries

The FortiGate-7000 sends all FortiGuard web filtering and spam filtering rating queries through a management interface from the management VDOM.

Web filtering quotas

On a VDOM operating with the Inspection Mode set to Proxy, you can go to Security Profiles > Web Filter and set up Category Usage Quotas. Each FPM has its own quota, and the FortiGate-7000 applies quotas per FPM and not per the entire FortiGate-7000 system. This could result in quotas being exceeded if sessions for the same user are processed by different FPMs.

Log messages include a slot field

An additional "slot" field has been added to log messages to identify the FPM that generated the log.

FortiOS Carrier

You have to apply a FortiOS Carrier license separately to each FIM and FPM to license a FortiGate-7000 for FortiOS Carrier.

Special notice for new deployment connectivity testing

Only the primary FPM can successfully ping external IP addresses. During a new deployment, while performing connectivity testing from the Fortigate-7000, make sure to run execute ping tests from the primary FPM CLI.

FortiGate-7000 v5.6.11 special features and limitations

This section describes special features and limitations for FortiGate-7000 v5.6.11.

Managing the FortiGate-7000

Management is only possible through the MGMT1 to MGMT4 front panel management interfaces. By default the MGMT1 to MGMT4 interfaces of the FIMs in slot 1 and slot 2 are in a single static aggregate interface named mgmt with IP address 192.168.1.99. You manage the FortiGate-7000 by connecting any one of these eight interfaces to your network, opening a web browser and browsing to the management IP address. For a factory default configuration, browse to https://192.168.1.99.

Note The FortiGate-7030E has one FIM and the MGMT1 to MGMT4 interfaces of that module are the only interfaces in the aggregate interface.

Default management VDOM

By default the FortiGate-7000 configuration includes a management VDOM named mgmt-vdom. For the FortiGate-7000 system to operate normally you should not change the configuration of this VDOM and this VDOM should always be the management VDOM. You should also not add or remove interfaces from this VDOM.

You have full control over the configurations of other FortiGate-7000 VDOMs.

Default Security Fabric configuration

The FortiGate-7000 uses the Security Fabric for communication and synchronization among FIMs and FPMs. Changing the default Security Fabric configuration could disrupt this communication and affect system performance.

Default Security Fabric configuration:

config system csf

set status enable

set configuration-sync local

set management-ip 0.0.0.0

set management-port 0

end

For the FortiGate-7000 to operate normally, you must not change the Security Fabric configuration.

Maximum number of LAGs and interfaces per LAG

FortiGate-7000 systems support up to 16 link aggregation groups (LAGs). This includes both normal link aggregation groups and redundant interfaces and including the redundant interface that contains the M1 to M4 management interfaces. A FortiGate-7000 LAG can include up to 20 interfaces.

Firewall

TCP sessions with NAT enabled that are expected to be idle for more than the distributed processing normal TCP timer (which is 3605 seconds) should only be distributed to the master FPM using a flow rule. You can configure the distributed normal TCP timer using the following command:

config system global

set dp-tcp-normal-timer <timer>

end

UDP sessions with NAT enabled that are expected to be idle for more than the distributed processing normal UDP timer should only be distributed to the primary FPM using a flow rule.

IP multicast

IPv4 and IPv6 Multicast traffic is only sent to the primary FPM (usually the FPM in slot 3). This is controlled by the following configuration:

config load-balance flow-rule

edit 18

set status enable

set vlan 0

set ether-type ipv4

set src-addr-ipv4 0.0.0.0 0.0.0.0

set dst-addr-ipv4 224.0.0.0 240.0.0.0

set protocol any

set action forward

set forward-slot master

set priority 5

set comment "ipv4 multicast"

next

edit 19

set status enable

set vlan 0

set ether-type ipv6

set src-addr-ipv6 ::/0

set dst-addr-ipv6 ff00::/8

set protocol any

set action forward

set forward-slot master

set priority 5

set comment "ipv6 multicast"

end

High availability

Only the M1 and M2 interfaces are used for the HA heartbeat communication. For information on how to set up HA heartbeat communication using the M1 and M2 interfaces, see Connect the M1 and M2 interfaces for HA heartbeat communication

The following FortiOS HA features are not supported or are supported differently by FortiGate-7000 v5.6.11:

  • Active-active HA is not supported.
  • The range for the HA group-id is 0 to 31.
  • Failover logic for FortiGate-7000 HA is not the same as FGCP for other FortiGate clusters.
  • HA heartbeat configuration is specific to FortiGate-7000 systems and differs from standard HA.
  • FortiGate Session Life Support Protocol (FGSP) HA (also called standalone session synchronization) is not supported.
  • FortiGate-7000 HA does not support the route-ttl, route-wait, and route-hold options for tuning route synchronization between FortiGate-7000s.
  • VLAN monitoring using the config system ha-monitor command is not supported.

Use of the diagnose sys ha checksum cluster command not recommended

The FortiGate-7000 uses a custom FGCP HA implementation and the diagnose sys ha checksum cluster command may show incorrect checksums so can't be used to check cluster synchronization. Instead you can log into the primary FIM of each FortiGate-7000 in the cluster and use the diagnose sys confsync showcsum and compare the results.

Shelf manager module

It is not possible to access SMM CLI using Telnet or SSH. Only console access is supported using the chassis front panel console ports as described in the FortiGate-7000 system guide.

For monitoring purpose, IPMI over IP is supported on SMM Ethernet ports. See your FortiGate-7000 system guide for details.

FortiOS features not supported by FortiGate-7000 v5.6.11

The following mainstream FortiOS 5.6.11 features are not supported by the FortiGate-7000 v5.6.11:

  • Hardware switch
  • Usage-based ECMP load balancing is not supported. If the config system settings v4-ecmp-mode option is set to usage-based, all traffic uses the first ECMP route instead of being load balanced among all ECMP routes. All other ECMP load balancing options are supported, including source-ip-based, weight-based, and source-dest-ip-based.
  • Switch controller
  • WiFi controller
  • WAN load balancing (SD-WAN)
  • IPv4 over IPv6, IPv6 over IPv4, IPv6 over IPv6 features
  • GRE tunneling is only supported after creating a load balance flow rule, for example:

    config load-balance flow-rule

    edit 0

    set status enable

    set vlan 0

    set ether-type ip

    set protocol gre

    set action forward

    set forward-slot master

    set priority 3

    end

  • Hard disk features including, WAN optimization, web caching, explicit proxy content caching, disk logging, and GUI-based packet sniffing.
  • The FortiGate-7000 platform only supports quarantining files to FortiAnalyzer.
  • Log messages should be sent only using the management aggregate interface
  • The FortiGate-7000 does not support configuring dedicated management interfaces using the config system dedicated-mgmt command or by enabling the dedicated-to management interface option.

IPsec VPN tunnels terminated by the FortiGate-7000

For a list of new FortiOS 5.6 FortiGate-7000 IPsec VPN features and a list of IPsec VPN features not supported by FortiOS 5.6 FortiGate-7000 IPsec VPN, see New IPsec VPN features.

SSL VPN

Sending all SSL VPN sessions to the primary FPM is recommended. You can do this by:

  • Creating a flow rule that sends all sessions that use the SSL VPN destination port and IP address to the primary FPM.
  • Creating flow rules that send all sessions that use the SSL VPN IP pool addresses to the primary FPM.

For more information about FortiGate-7000 SSL VPN support, see SSL VPN load balancing.

Traffic shaping and DDoS policies

Each FPM applies traffic shaping and DDoS quotas independently. Because of load-balancing, this may allow more traffic than expected.

FortiGuard web filtering and spam filtering queries

The FortiGate-7000 sends all FortiGuard web filtering and spam filtering rating queries through a management interface from the management VDOM.

Web filtering quotas

On a VDOM operating with the Inspection Mode set to Proxy, you can go to Security Profiles > Web Filter and set up Category Usage Quotas. Each FPM has its own quota, and the FortiGate-7000 applies quotas per FPM and not per the entire FortiGate-7000 system. This could result in quotas being exceeded if sessions for the same user are processed by different FPMs.

Log messages include a slot field

An additional "slot" field has been added to log messages to identify the FPM that generated the log.

FortiOS Carrier

You have to apply a FortiOS Carrier license separately to each FIM and FPM to license a FortiGate-7000 for FortiOS Carrier.

Special notice for new deployment connectivity testing

Only the primary FPM can successfully ping external IP addresses. During a new deployment, while performing connectivity testing from the Fortigate-7000, make sure to run execute ping tests from the primary FPM CLI.