Fortinet black logo

Admin Guide (Standalone)

Target

Copy Link
Copy Doc ID 015f89e6-2d48-11ec-9c99-00505692583a:917833
Download PDF

Target

Target is the network connected to FortiExtender (Standalone). It is usually an up-link network, such as an NSP network provided by a wireless carrier. A target consists of an outgoing interface and a next hop. Targets are always used in routing systems and SD-WANs to define the destination network to which traffic is sent.

The table below describes the commands for setting a target.

CLI command

Description

config router target

Enters target configuration mode.

edit <name>

Specify the target network.

set interface <interface>

Specify the outgoing interface of the gateway.

set next-hop <next_hop>

Specify the IP address of the next-hop gateway.

Example target configuration:
# get system interface
== [ lo ]
name: lo status: online/up/link up type: loopback mac:
00:00:00:00:00:00 mode: static ip: 127.0.0.1/8 mtu: 65536
gateway: 0.0.0.0
== [ eth1 ]
name: eth1 status: online/up/link up type: lte mac:
9a:fd:56:f1:1a:08 mode: dhcp ip: 10.118.38.4/29 mtu: 1500
gateway: 10.118.38.5 dns: 172.26.38.1
== [ nas1 ]
name: nas1 status: online/up/link up type: physical mac:
70:4c:a5:fd:1b:38 mode: dhcp ip: 172.24.236.22/22 mtu: 1500
gateway: 172.24.239.254 dns: 172.30.1.105, 172.30.1.106
# config router target
(target) # edit target.lte
(target/lte) <M> # abort
(target) # edit target.lte
(target.lte) <M> # set interface eth1
(target.lte) <M> # set next-hop 10.118.38.5
(target.lte) <M> # next
(target) # end

A target is automatically created when an LTE is connected, with the LTE as the outgoing interface and the gateway as the next hop. The next hop is not mandatory if the outgoing interface is a tunnel interface or a Virtual-WAN interface. For example:

edit target.fcs-1-phase-1

set interface fcs-1-phase-1

set next-hop

next

edit target.vwan1

set interface vwan1

set next-hop

next

Target

Target is the network connected to FortiExtender (Standalone). It is usually an up-link network, such as an NSP network provided by a wireless carrier. A target consists of an outgoing interface and a next hop. Targets are always used in routing systems and SD-WANs to define the destination network to which traffic is sent.

The table below describes the commands for setting a target.

CLI command

Description

config router target

Enters target configuration mode.

edit <name>

Specify the target network.

set interface <interface>

Specify the outgoing interface of the gateway.

set next-hop <next_hop>

Specify the IP address of the next-hop gateway.

Example target configuration:
# get system interface
== [ lo ]
name: lo status: online/up/link up type: loopback mac:
00:00:00:00:00:00 mode: static ip: 127.0.0.1/8 mtu: 65536
gateway: 0.0.0.0
== [ eth1 ]
name: eth1 status: online/up/link up type: lte mac:
9a:fd:56:f1:1a:08 mode: dhcp ip: 10.118.38.4/29 mtu: 1500
gateway: 10.118.38.5 dns: 172.26.38.1
== [ nas1 ]
name: nas1 status: online/up/link up type: physical mac:
70:4c:a5:fd:1b:38 mode: dhcp ip: 172.24.236.22/22 mtu: 1500
gateway: 172.24.239.254 dns: 172.30.1.105, 172.30.1.106
# config router target
(target) # edit target.lte
(target/lte) <M> # abort
(target) # edit target.lte
(target.lte) <M> # set interface eth1
(target.lte) <M> # set next-hop 10.118.38.5
(target.lte) <M> # next
(target) # end

A target is automatically created when an LTE is connected, with the LTE as the outgoing interface and the gateway as the next hop. The next hop is not mandatory if the outgoing interface is a tunnel interface or a Virtual-WAN interface. For example:

edit target.fcs-1-phase-1

set interface fcs-1-phase-1

set next-hop

next

edit target.vwan1

set interface vwan1

set next-hop

next