Fortinet black logo

FortiWiFi and FortiAP Configuration Guide

Configuring the network interface for the AP unit

Copy Link
Copy Doc ID 89ea0dba-bc2e-11ec-9fd1-fa163e15d75b:434872
Download PDF

Configuring the network interface for the AP unit

The interface to which you connect your wireless access point needs an IP address. No administrative access, DNS Query service or authentication should be enabled.

In this example, the FortiAP units connect to port3 and are controlled through IP addresses on the 10.10.70.0/24 network.

To configure the interface for the AP unit - GUI
  1. Go to Network > Interfaces, and edit the interface to which the AP unit connects (in this example, port3).
  2. In Addressing mode, select Manual.
  3. In IP/Network Mask, enter an IP address and netmask for the interface (in this example, 10.10.70.1/255.255.255.0).

  4. In the Administrative Access section, go to IPv4 and select the Security Fabric Connection checkbox.
  5. When FortiAP units are connected to the interface on FortiGate (directly or through a switch), you can go to the Edit Interface section and set the Role to LAN.

    Selecting the LAN role loads the DHCP Server toggle. If you enable DHCP Server, the GUI can automatically set the DHCP IP range based on the interface IP address.

  6. Click OK.

If you enable DHCP Server, you can also specify the Wireless controller IP address from under the Advanced section.

To configure the interface for the AP unit - CLI

In the CLI, you must configure the interface IP address and DHCP server separately.

config system interface

edit "port3"

set mode static

set ip 10.10.70.1 255.255.255.0

set allowaccess fabric

next

end

config system dhcp server

edit 3

set interface "port3"

config ip-range

edit 1

set start-ip 10.10.70.2

set end-ip 10.10.70.254

next

end

set default-gateway 10.10.70.1

set netmask 255.255.255.0

set vci-match enable

set vci-string "FortiAP"

next

end

The optional vci-match and vci-string fields ensure that the DHCP server will provide IP addresses only to FortiAP units.

Understanding FortiWiFi aplink interface

The aplink link interface is an interface unique to certain FortiWiFi models, including but not limited to FWF-80F-2R and FWF-81F-2R. It acts as an internal trunk interface between the FortiAP and FortiGate. The aplink1 and aplink2 members are physical interfaces between the FortiAP and the FortiGate.

You can edit the aplink interface to change the subnet IP, however, the DHCP server should not be edited as it can cause the internal AP to stop working and lead to loss of WiFi capability on the AP.

To configure the aplink interface - CLI
config system interface
  edit "aplink"
    set vdom "root"
    set ip 192.168.80.1 255.255.255.0
    set allowaccess ping fabric
    set type aggregate
    set member "aplink1" "aplink2"
    set device-identification enable
  next
end

Configuring the network interface for the AP unit

The interface to which you connect your wireless access point needs an IP address. No administrative access, DNS Query service or authentication should be enabled.

In this example, the FortiAP units connect to port3 and are controlled through IP addresses on the 10.10.70.0/24 network.

To configure the interface for the AP unit - GUI
  1. Go to Network > Interfaces, and edit the interface to which the AP unit connects (in this example, port3).
  2. In Addressing mode, select Manual.
  3. In IP/Network Mask, enter an IP address and netmask for the interface (in this example, 10.10.70.1/255.255.255.0).

  4. In the Administrative Access section, go to IPv4 and select the Security Fabric Connection checkbox.
  5. When FortiAP units are connected to the interface on FortiGate (directly or through a switch), you can go to the Edit Interface section and set the Role to LAN.

    Selecting the LAN role loads the DHCP Server toggle. If you enable DHCP Server, the GUI can automatically set the DHCP IP range based on the interface IP address.

  6. Click OK.

If you enable DHCP Server, you can also specify the Wireless controller IP address from under the Advanced section.

To configure the interface for the AP unit - CLI

In the CLI, you must configure the interface IP address and DHCP server separately.

config system interface

edit "port3"

set mode static

set ip 10.10.70.1 255.255.255.0

set allowaccess fabric

next

end

config system dhcp server

edit 3

set interface "port3"

config ip-range

edit 1

set start-ip 10.10.70.2

set end-ip 10.10.70.254

next

end

set default-gateway 10.10.70.1

set netmask 255.255.255.0

set vci-match enable

set vci-string "FortiAP"

next

end

The optional vci-match and vci-string fields ensure that the DHCP server will provide IP addresses only to FortiAP units.

Understanding FortiWiFi aplink interface

The aplink link interface is an interface unique to certain FortiWiFi models, including but not limited to FWF-80F-2R and FWF-81F-2R. It acts as an internal trunk interface between the FortiAP and FortiGate. The aplink1 and aplink2 members are physical interfaces between the FortiAP and the FortiGate.

You can edit the aplink interface to change the subnet IP, however, the DHCP server should not be edited as it can cause the internal AP to stop working and lead to loss of WiFi capability on the AP.

To configure the aplink interface - CLI
config system interface
  edit "aplink"
    set vdom "root"
    set ip 192.168.80.1 255.255.255.0
    set allowaccess ping fabric
    set type aggregate
    set member "aplink1" "aplink2"
    set device-identification enable
  next
end