Fortinet black logo

FortiWiFi and FortiAP Configuration Guide

Viewing device location data on a FortiGate unit

Viewing device location data on a FortiGate unit

You can use the FortiGate CLI to list located devices. This is mainly useful to confirm that the location data feature is working, You can also reset device location data.

To list located devices

diag wireless-controller wlac -c sta-locate

To reset device location data

diag wireless-controller wlac -c sta-locate-reset

Example output

The following output shows data for three WiFi devices.

FWF60C3G11004319 # diagnose wireless-controller wlac -c sta-locate

sta_mac vfid rid base_mac freq_lst frm_cnt frm_fst frm_last intv_sum intv2_sum intv3_sum intv_min intv_max signal_sum signal2_sum signal3_sum sig_min sig_max sig_fst sig_last ap

00:0b:6b:22:82:61 0

FAP22B3U11005354 0 0 00:09:0f:f1:bb:e4 5745 257 708 56 651 1836 6441 0 12 -21832 1855438 -157758796 -88 -81 -84 -88 0

00:db:df:24:1a:67 0

FAP22B3U11005354 0 0 00:09:0f:f1:bb:e4 5745 42 1666 41 1625 97210 5831613 0 60 -3608 310072 -26658680 -90 -83 -85 -89 0

10:68:3f:50:22:29 0

FAP22B3U11005354 0 0 00:09:0f:f1:bb:e4 5745 102 1623 58 1565 94136 5664566 0 60 -8025 631703 -49751433 -84 -75 -78 -79 0

The output for each device appears on two lines. The first line contains only the device MAC address and the VLAN ID. The second line begins with the ID (serial number) of the FortiWiFi or FortiAP unit that detected the device, the AP MAC address, and then the fields that the Euclid service uses. Because of its length, this line wraps around and displays as multiple lines.

Viewing device location data on a FortiGate unit

Viewing device location data on a FortiGate unit

You can use the FortiGate CLI to list located devices. This is mainly useful to confirm that the location data feature is working, You can also reset device location data.

To list located devices

diag wireless-controller wlac -c sta-locate

To reset device location data

diag wireless-controller wlac -c sta-locate-reset

Example output

The following output shows data for three WiFi devices.

FWF60C3G11004319 # diagnose wireless-controller wlac -c sta-locate

sta_mac vfid rid base_mac freq_lst frm_cnt frm_fst frm_last intv_sum intv2_sum intv3_sum intv_min intv_max signal_sum signal2_sum signal3_sum sig_min sig_max sig_fst sig_last ap

00:0b:6b:22:82:61 0

FAP22B3U11005354 0 0 00:09:0f:f1:bb:e4 5745 257 708 56 651 1836 6441 0 12 -21832 1855438 -157758796 -88 -81 -84 -88 0

00:db:df:24:1a:67 0

FAP22B3U11005354 0 0 00:09:0f:f1:bb:e4 5745 42 1666 41 1625 97210 5831613 0 60 -3608 310072 -26658680 -90 -83 -85 -89 0

10:68:3f:50:22:29 0

FAP22B3U11005354 0 0 00:09:0f:f1:bb:e4 5745 102 1623 58 1565 94136 5664566 0 60 -8025 631703 -49751433 -84 -75 -78 -79 0

The output for each device appears on two lines. The first line contains only the device MAC address and the VLAN ID. The second line begins with the ID (serial number) of the FortiWiFi or FortiAP unit that detected the device, the AP MAC address, and then the fields that the Euclid service uses. Because of its length, this line wraps around and displays as multiple lines.