Configuring log forwarding
Forwarding mode only requires configuration on the client side. No configuration is needed on the server side. In aggregation mode, accepting the logs must be enabled on the FortiAnalyzer that is acting as the server.
Forwarding mode
Forwarding mode can be configured in the GUI. No configuration is required on the server side.
To configure the client:
- Go to System Settings > Log Forwarding.
- Click Create New in the toolbar. The Create New Log Forwarding pane opens.
- Fill in the information as per the below table, then click OK to create the new log forwarding. The FortiAnalyzer device will start forwarding logs to the server.
Name
Enter a name for the remote server.
Status
Set to On to enable log forwarding. Set to Off to disable log forwarding.
Remote Server Type
Select the type of remote server to which you are forwarding logs: FortiAnalyzer, Syslog, or Common Event Format (CEF).
Server IP
Enter the IP address of the remote server.
Server Port
Enter the server port number. Default: 514.
This option is only available when the server type in not FortiAnalyzer.
Reliable Connection
Turn on to use TCP connection. Turn off to use UDP connection.
If you want to forward logs to a Syslog or CEF server, ensure this option is supported.
RELP is not supported.
If the connection goes down, logs are buffered and automatically forwarded when the connection is restored. See Log forwarding buffer.
Sending Frequency
Select when logs will be sent to the server: Real-time, Every 1 Minute, or Every 5 Minutes (default).
This option is only available when the server type is FortiAnalyzer.
Log Forwarding Filters
Device Filters
Click Select Device, then select the devices whose logs will be forwarded.
Log Filters
Turn on to configure filter on the logs that are forwarded.
Select All or Any of the Following Conditions in the Log messages that match field to control how the filters are applied to the logs.
Add filters to the table by selecting the Log Field, Match Criteria, and Value for each filter.
Enable Exclusions
This option is only available when the remove server is a Syslog or CEF server.
Turn on to configure filter on the logs that are forwarded.
Add exclusions to the table by selecting the Device Type and Log Type. Then, add Log Fields to the Exclusion List by clicking Fields and specifying the excluded log fields in the Select Log Field pane.
|
Devices whose logs are being forwarded to another FortiAnalyzer device are added to the server as unauthorized devices. To authorize devices, see Authorizing devices. |
Aggregation mode
Aggregation mode can only be configured using the CLI. Aggregation mode configurations are not listed in the GUI table, but still use a log forwarding ID number.
|
|
Use the following CLI command to see what log forwarding IDs have been used: get system log-forward |
To configure the server:
- If required, create a new administrator with the Super_User profile. See Creating administrators.
- Enable log aggregation and, if necessary, configure the disk quota, with the following CLI commands:
config system log-forward-service
set accept-aggregation enable
set aggregation-disk-quota <quota>
end
To configure the client:
- Open the log forwarding command shell:
config system log-forward
- Create a new, or edit an existing, log forwarding entry:
edit <log forwarding ID>
- Set the log forwarding mode to
aggregation:set mode aggregation
- Set the server display name and IP address:
set server-name <string>
set server-ip <xxx.xxx.xxx.xxx>
- Enter the user name and password of the super user administrator on the server:
set agg-user <string>
set agg-password <string>
- If required, set the aggregation time from 0 to 23 hours (default: 0, or midnight):
set agg-time <integer>
- Enter the following to apply the configuration and create the log aggregation:
end
The following line will be displayed to confirm the creation of the log aggregation:
check for cfg[<log forwarding ID>] svr_disp_name=<server-name>
|
|
For more information, see the FortiAnalyzer CLI Reference. |